Pallet Cabnet
![temp_1223805956.jpg](/proxy/?url=https://content.instructables.com/FAD/QBUB/IBGCLI3W/FADQBUBIBGCLI3W.jpg&filename=temp_1223805956.jpg)
tools -
hammer
power saw
nails/screws
stain
gloss
hinges
hammer
power saw
nails/screws
stain
gloss
hinges
Building the Base
![temp_1753043809.jpg](/proxy/?url=https://content.instructables.com/F1W/TVEM/IBGCLI4F/F1WTVEMIBGCLI4F.jpg&filename=temp_1753043809.jpg)
![temp_-1018632021.jpg](/proxy/?url=https://content.instructables.com/FW3/KE3H/IBGCLI5V/FW3KE3HIBGCLI5V.jpg&filename=temp_-1018632021.jpg)
first step was to build the base in which the cabnet will be based on.
Building the Sides
![temp_-1582087657.jpg](/proxy/?url=https://content.instructables.com/FF5/P2YU/IBGCLI6F/FF5P2YUIBGCLI6F.jpg&filename=temp_-1582087657.jpg)
![temp_712398385.jpg](/proxy/?url=https://content.instructables.com/F6T/SB4A/IBGCLI6J/F6TSB4AIBGCLI6J.jpg&filename=temp_712398385.jpg)
once the base was done it was time to build the walls. i made each panel seperate. it was a bit hard to get them square since the pallets were all different thicknesses and shapes
Putting on the Top
![temp_-1080912314.jpg](/proxy/?url=https://content.instructables.com/FUC/CWDH/IBGCLI6Q/FUCCWDHIBGCLI6Q.jpg&filename=temp_-1080912314.jpg)
![temp_974180930.jpg](/proxy/?url=https://content.instructables.com/F5L/ZQDL/IBGCLI6U/F5LZQDLIBGCLI6U.jpg&filename=temp_974180930.jpg)
putting on the top of the cabnet wasnt too bad. just had to cute a bunch of timbers at the same length and then rip the last one down to get the desired width.
Doors and Divider
![temp_909450921.jpg](/proxy/?url=https://content.instructables.com/F84/5WC2/IBGCLI70/F845WC2IBGCLI70.jpg&filename=temp_909450921.jpg)
![temp_-1773715932.jpg](/proxy/?url=https://content.instructables.com/FQ1/MKUP/IBGCLI72/FQ1MKUPIBGCLI72.jpg&filename=temp_-1773715932.jpg)
![temp_573711019.jpg](/proxy/?url=https://content.instructables.com/FHR/SD0W/IBGCLI79/FHRSD0WIBGCLI79.jpg&filename=temp_573711019.jpg)
![temp_1856707800.jpg](/proxy/?url=https://content.instructables.com/FQL/JMRO/IBGCLI7C/FQLJMROIBGCLI7C.jpg&filename=temp_1856707800.jpg)
building the divider was easy. a few measurements and then just nailing them in.
bulding the doors was the same. i divided the space and that became the door width. i found some old hinges to use for the doors and for the door knobs i found some old draw handles and knobs and used those
bulding the doors was the same. i divided the space and that became the door width. i found some old hinges to use for the doors and for the door knobs i found some old draw handles and knobs and used those
Building the Shelf and Painting
![temp_-785304121.jpg](/proxy/?url=https://content.instructables.com/FE2/WJXW/IBGCLI7E/FE2WJXWIBGCLI7E.jpg&filename=temp_-785304121.jpg)
![temp_-1838179477.jpg](/proxy/?url=https://content.instructables.com/FQE/6UA9/IBGCLI7H/FQE6UA9IBGCLI7H.jpg&filename=temp_-1838179477.jpg)
![temp_-490025645.jpg](/proxy/?url=https://content.instructables.com/FPO/AORJ/IBGCLI8I/FPOAORJIBGCLI8I.jpg&filename=temp_-490025645.jpg)
![temp_-1814611223.jpg](/proxy/?url=https://content.instructables.com/FDD/6JW6/IBGCLI9N/FDD6JW6IBGCLI9N.jpg&filename=temp_-1814611223.jpg)
the last part of the build was to put in a shelf which would house all the records which this build was designed for.
after that i stained the cabnet with a dark mahogany stain which i found. i then went over the top with a jarrah stain to bring some red through and also give some areas a totally different colour eg. the doors.
after that i stained the cabnet with a dark mahogany stain which i found. i then went over the top with a jarrah stain to bring some red through and also give some areas a totally different colour eg. the doors.
Finished
![temp_-405813425.jpg](/proxy/?url=https://content.instructables.com/FGH/ULN2/IBGCLIDQ/FGHULN2IBGCLIDQ.jpg&filename=temp_-405813425.jpg)
![temp_171562884.jpg](/proxy/?url=https://content.instructables.com/FIB/FR0B/IBGCLIER/FIBFR0BIBGCLIER.jpg&filename=temp_171562884.jpg)
lastly i went over with a few coats of gloss. then she was all done!