Easy Lego M&m Dispenser

by seanthesheep101 in Living > LEGO & K'NEX

14172 Views, 50 Favorites, 0 Comments

Easy Lego M&m Dispenser

P1050162.JPG
do you love m&ms and Lego? then this is the instructable for you

Step 1

P1050129.JPG
first your going to need a bottom piece at least 10 by 8 and put on a double slope and next to it put on a single slope 2 from either sides

Step 2

P1050130.JPG
P1050131.JPG
P1050132.JPG
P1050133.JPG
P1050134.JPG
then you have to make a piece that is 3 by 4 2 layers high and covered in flats. then put it next to the slopes so that it is flush with the back.

Step 3

P1050136.JPG
P1050138.JPG
P1050139.JPG
P1050140.JPG
P1050141.JPG
P1050135.JPG
then you need to make a piece like this that has a 2 by 2 hole in it so the outer border is 4 by 4 and put flats all around the sides except 2 middle ones. then get a 2 by 6 thin piece and cover with flats join the front of the 2 by 6 to the 4 by 4 square with hole in it where their are no flats.

Step 4

P1050167.JPG
both lego pieces.jpg
then put bricks all around the outside to make walls but have a gap where the m&ms come out of. dont forget to put the square flat where it shows you because it makes the mechanism slide.

Step 5

P1050144.JPG
P1050145.JPG
put the next layer of bricks on that will cover the mechanism which is the 4 by 4 with hole in it with the 6 by 2. to put that in it have the square in the box with the 6 by 2 out of the box as you can see in the pic. now it should be 5 layers up with the part where you can pull out the side on the 4th ;layer

Step 6

more lego pieces together.jpg
make a piece that is a 2 by 4 joined with a 1 by 2 and put it in the inside as shown. to put the 2 pieces together put the 1 by 2 on the under side of the 2 by 4 in the middle up the back

Step 7

P1050150.JPG
then put another layer on the top so it is in line with the piece that you put on in the step before. put the layer on so that it looks like this

Step 8

put the layer on like so.jpg
put the next layer on so that when the m&ms are in it falls down to that spot. have slopes from all ends.

Step 9

P1050152.JPG
P1050153.JPG
nearly done.jpg
then make a box with no top or bottom and a hole through the middle so that it fits the top of the box and so that it is 3 layers high. you can make it as high as you want but i thought it looked better (and because i had no more pieces) then put it on top of the other piece

Step 10

P1050155.JPG
P1050156.JPG
P1050157.JPG
P1050158.JPG
P1050159.JPG
once you have done that then you can make a lid. you can make an easy one that is a thin piece that is 8 by 6. or you can go the harder way (not that hard) but is better. you will need a trap door that is 8 by 10 on the outside and the door is 5 by 4, then get a 1 by 8 thin piece or 2 1 by 4 thin pieces and put them on the front of the trap door where the hinge is not and then put a 1 by 2 single layer in the middle of where the 1 by 8 is. and your done to use this dispenser open the lid and put as many mini m&ms that you can fit in the lid then close the lid and pull out the knob that is on the side until it stops and then push it back in again and they should fall out in front of you

Have a Fun Yummy Time :)


i hope this really helped with anything at all

pls comment and ask as many Qs as you want  ;)