Yellow Citrine Faux Gemstone Points & Pendants

by Rhonda Chase Design in Craft > Jewelry

1077 Views, 30 Favorites, 0 Comments

Yellow Citrine Faux Gemstone Points & Pendants

IMG_8824.JPG
IMG_8825.JPG
IMG_8781.JPG
IMG_8816.JPG

Citrine is a beautiful yellow quartz crystal often used to make jewelry. The most coveted citrine is lemon yellow with excellent clarity. These clear yellow gems are the most expensive citrine stones, but we can easily reproduce them in resin.

In this tutorial I'll show you how to create realistic citrine gemstone points, and turn them into gorgeous pendants.

What You Need

IMG_8814.JPG
IMG_8776.JPG
IMG_8730.JPG
IMG_8760.JPG
IMG_8731.JPG

Resin of your choice (clear) - I'm using polyester resin for this project

Mixing cups, stirrers, gloves

Respirator mask

Yellow transparent alcohol dye

Gemstone molds

Gemstone point mold

Piece of parchment or wax paper

Newspaper, mat, or other surface protector

Great ventilation - I'm working outside

Jewelry findings - 2-3" headpins, beads caps, jump rings

Round nose pliers, Flat nose pliers

Begin

IMG_8732.JPG
IMG_8734.JPG

Take out all your resin supplies and set them up so you don't have to find things with sticky hands. Pour about an ounce of resin into a mixing cup. If you're using polyester resin do NOT add the hardener yet. If you're using epoxy resin, mix a half ounce of each part for 1 ounce total. Only use UV resin if your molds are perfectly clear.

Color

IMG_8735.JPG
IMG_8736.JPG
IMG_8737.JPG

Different brands of alcohol dye have different concentrations, so start by adding only one drop of yellow dye to your resin. If it barely shows add another drop or two, once you see a light yellow tint, mix gently and thoroughly.

Adjust Color

IMG_8738.JPG
IMG_8739.JPG
IMG_8740.JPG
IMG_8741.JPG

Keep adding 1-2 drops of dye at a time, and then stir again, until you reach a bright, light yellow. The exact tint is up to you - citrine comes in gradations from barely yellow to and darker, almost orange hue.

Pro Tip:

When you're getting close to the desired color, bring it into a different light. I was working in the shade, so I brought it into the sun to check the color.

Hardener

IMG_8748.JPG
IMG_8749.JPG

If you're using polyester resin, now is the time to add a drop or two of hardener. (The more drops, the faster it cures.)

Mold

IMG_8750.JPG
IMG_8751.JPG
IMG_8755.JPG

Carefully pour the resin into your point mold. Make sure it gets all the way to the bottom without bubbles. If you do see a bubble or air pocket, poke it with a toothpick.

Keep Molding

IMG_8752.JPG
IMG_8753.JPG
IMG_8758.JPG

Pour resin into the rest of your point and gemstone molds. Set the molds on a flat surface.

If you have any resin leftover, pour it onto a piece of wax or parchment paper. This is so you can see how your resin is curing without disturbing your molds.

Occasionally test the thickness of the resin with the head part of a head pin.

Wait

IMG_8756.JPG
IMG_8754.JPG
IMG_8759.JPG

Testing, Testing

IMG_8764.JPG
IMG_8765.JPG
IMG_8766.JPG
IMG_8770.JPG

Test the resin with a headpin occasionally until the resin has a jelly-like consistency. The headpin should be able to dent the resin before poking through.

When the resin reaches this stage, gently poke through the top of the point mold resin and insert the headpin about 1/4-1/2". If the resin is the right consistency, the pin will remain straight up and be permanently attached to the resin.

Repeat with all of your vertical molds.

Wait Again

IMG_8767.JPG
IMG_8768.JPG
IMG_8769.JPG
IMG_8771.JPG

Leave undisturbed to cure the rest of the way.

You can use your extra resin to continue testing for hardness.

Unmold

IMG_8774.JPG
IMG_8775.JPG
IMG_8781.JPG

The "gemstones" will pop out easily.

The points will require some gentle coaxing. You can use the headpin to help pull the cured resin out of the vertical molds.

Make a Pendant

IMG_8784.JPG
IMG_8785.JPG
IMG_8794.JPG

Since the head pin is permanently attached, you can string any kind of bead caps and beads onto the wire for adornment. I used a filigree bead cone on my point, and a bead cap and beads on the cylinder. The bead cone was made from a thin metal, so I was able to bend it to fit the point.

When choosing the right findings, see if there's anything you need to hide, like the headpin.

Secure Findings

IMG_8786.JPG
IMG_8787.JPG
IMG_8788.JPG
IMG_8790.JPG
IMG_8791.JPG

To secure the caps, cones, and beads, you'll make a wrapped loop right above the top finding on each pendant as shown. (See step 6 in this earring Instructable for detailed wrapped loop instructions.)

Wrap the wire tail around the top of the cone or top bead. This will hold everything in place, but if you want extra security, you can add a drop of E6000 or other jewelry glue.

Finish Pendant

IMG_8792.JPG
IMG_8793.JPG
IMG_8795.JPG
IMG_8803.JPG

Add a jump ring to each wrapped loop. Now your faux citrine pendant is ready for a chain!

Enjoy!

IMG_8822.JPG
IMG_8800Crop.jpg
IMG_8782yellow.jpg
IMG_8820.JPG

These faux citrine points lend themselves to lots of possibilities:

You can either get the classic point molds or a variety of other shapes. You can use any assortment of findings or get creative and make your own. You can even experiment with using other materials for your cap like aluminum foil or fabric. Or forget about the caps altogether and just make a simple loop for hanging.

Have fun and let me know how it goes if you try this project!