Wine Rack
![Wine Rack.png](/proxy/?url=https://content.instructables.com/F6U/FQP4/LAGSQYP6/F6UFQP4LAGSQYP6.png&filename=Wine Rack.png)
This is the perfect gift for loved ones or a friend
Supplies
![Materials.jpg](/proxy/?url=https://content.instructables.com/FJZ/VXVD/LAGSQYVR/FJZVXVDLAGSQYVR.jpg&filename=Materials.jpg)
Materials List
- 25″ of 1×6 = 1.042 BF
- 25″ of 1×8 = 1.389 BF
- 9″ of 1×2 = .125 BF
- 1 – 1x4x6′ = 2 BF
- 1-1/4″ Pocket Hole Screws
- 1-1/4″ Wood Screws
- 1-1/4″ Brad Nails
- Wood Glue
- Hanging Hardware
4.556 BF * $4.75 = $21.64
Cut List
- 1 – 1×6 @ 25″ (stemware hanger)
- 1 – 1×8 @ 25″ (back)
- 2 – 1×2 @ 4-1/4″ (sides)
- 2 – 1×4 @ 25″ (ledge and front)
- 2 – 1×4 @ 2-3/4″ (sides)
Tools
- Tape Measure
- Pencil
- Speed Square
- Drill with Countersink Drill Bit
- Circular Saw
- Kreg Jig
- Jigsaw
- Brad Nailer or Hammer
Base
![Step 1.jpg](/proxy/?url=https://content.instructables.com/FXM/QIP3/LAGSQZ45/FXMQIP3LAGSQZ45.jpg&filename=Step 1.jpg)
Using a jigsaw, cut out the stemware slots as shown
Attach Back
![Step 2.jpg](/proxy/?url=https://content.instructables.com/F18/QA0W/LAGSQZ7J/F18QA0WLAGSQZ7J.jpg&filename=Step 2.jpg)
Drill 3/4″ pocket holes into the back board facing down and use 1-1/4″ pocket hole screws to attach it to the stemware rack. Alternately, you can use 1-1/4″ brad nails and wood glue to build this wine rack.
Attach 1x2 Sides
![Step 3.jpg](/proxy/?url=https://content.instructables.com/FCY/TBWQ/LAGSQZ6Q/FCYTBWQLAGSQZ6Q.jpg&filename=Step 3.jpg)
Attach the 1×2 side pieces with 3/4″ pocket holes and 1-1/4″ pocket hole screws. Attach the 1×2 to the stemware rack with 1-1/4″ brad nails nailed from underneath.
Attach Ledge
![Step 4.jpg](/proxy/?url=https://content.instructables.com/FQQ/9IGS/LAGSQZ5X/FQQ9IGSLAGSQZ5X.jpg&filename=Step 4.jpg)
Drill 3/4″ pocket holes into the 1×4 ledge and attach it to the back with 1-1/4″ pocket hole screws. You can also nail in 1-1/4″ brad nails on top to attach the ledge to the 1×2 sides.
Attach 1x4 Sides
![Step 5.jpg](/proxy/?url=https://content.instructables.com/FIV/IFUN/LAGSQZ5D/FIVIFUNLAGSQZ5D.jpg&filename=Step 5.jpg)
Drill 3/4″ pocket holes into the 1×4 sides and attach it to the back with 1-1/4″ pocket hole screws. Use glue on the joint where it meets the ledge.
Attach Front
![Step 6.jpg](/proxy/?url=https://content.instructables.com/FFW/MJ1T/LAGSQZ4W/FFWMJ1TLAGSQZ4W.jpg&filename=Step 6.jpg)
Pre-drill countersunk pilot holes into the front board and attach with 1-1/4″ wood screws. Fill the holes with wood putty or wood plugs.