The Morse Code Generator by a PS\2 Keyboard
by giuliom95 in Circuits > Arduino
13286 Views, 20 Favorites, 0 Comments
The Morse Code Generator by a PS\2 Keyboard
Hi, all!
Today I' m trying to explain you my last project: "The morse code generator by a PS\2 keyboard"
I' ve used an PS/2 keyboard to send input to my Arduino board and transform it in morse code that activate a speaker and a relay.
Components:
- PS\2 keyboard
- Arduino Uno(or others)
- Wires
- 5V relay
- BC547 transistor
- Small speaker
- Recirculation Diode
Setting Hardware
The Fritzing project image below can explain almost all, but the hardest thing is connect the keyboard to the Arduino board. We must connect the PS\2 connector data pin to the Arduino pin 8, the clock pin to the 2nd, 5V pin to a 5V source and GND pin to GND. If you find a female PS\2 connector you are very lucky and can use it but others can do like me: I've use as replacement the metal part, covered by insulating tape, of connectors that are used on the mother boards (for wires of: power and HDD LEDs, power and reset buttons, USB face connectors , ecc. ecc.) .
Software and Conclusions
/**********
morse.ino
**********/
#include <PS2Keyboard.h>
const int DataPin = 8;
const int IRQpin = 2;
PS2Keyboard keyboard;
void setup() {
delay(1000);
keyboard.begin(DataPin, IRQpin);
}
void loop() {
if (keyboard.available()) {
char c = keyboard.read();
if (c == 'a') {
p();l();
} else if (c == 'b') {
l();p();p();p();
} else if (c == 'c') {
l();p();l();p();
} else if (c == 'd') {
l();p();p();
} else if (c == 'e') {
p();
} else if (c == 'f') {
p();p();l();p();
} else if (c == 'g') {
l();l();p();
} else if (c == 'h') {
p();p();p();p();
} else if (c == 'i') {
p();p();
} else if (c == 'j') {
p();l();l();l();
} else if (c == 'k') {
l();p();l();
} else if (c == 'l') {
p();l();p();p();
} else if (c == 'm') {
l();l();
} else if (c == 'n') {
l();p();
} else if (c == 'o') {
l();l();l();
} else if (c == 'p') {
p();l();l();p();
} else if (c == 'q') {
l();l();p();l();
} else if (c == 'r') {
p();l();p();
} else if (c == 's') {
p();p();p();
} else if (c == 't') {
l();
} else if (c == 'u') {
p();p();l();
} else if (c == 'v') {
p();p();p();l();
} else if (c == 'w') {
p();l();l();
} else if (c == 'x') {
l();p();p();l();
} else if (c == 'y') {
l();p();l();l();
} else if (c == 'z') {
l();l();p();p();
} else if (c == '1') {
p();l();l();l();l();
} else if (c == '2') {
p();p();l();l();l();
} else if (c == '3') {
p();p();p();l();l();
} else if (c == '4') {
p();p();p();p();l();
} else if (c == '5') {
p();p();p();p();p();
} else if (c == '6') {
l();p();p();p();p();
} else if (c == '7') {
l();l();p();p();p();
} else if (c == '8') {
l();l();l();p();p();
} else if (c == '9') {
l();l();l();l();p();
} else if (c == '0') {
l();l();l();l();l();
} else if (c == ' ') {
pausa();
} else {
tone(4, 300, 250); //error tone
}
}
}
void p(){ //dot
digitalWrite(12, HIGH);
tone(4, 700);
delay(250);
digitalWrite(12, LOW);
noTone(4);
delay(250);
}
void l(){ //dash
digitalWrite(12, HIGH);
tone(4, 700);
delay(750);
digitalWrite(12,LOW);
noTone(4);
delay(250);
}
void pausa(){ //pause between two letters
delay(1750);
}
If you have any kind of problems leave a comment