Captains Log Steambook

This is a Steampunk inspired paper note receptacle perfect for using ink or other products to  make a mark for future referral back to. We all need a place to keep our plans for overworld domination, now you can have one! This sea weathered steam punk Captains log book will let you keep track of where you have been, so you never have to go back and also plans or maps or even recipes for home made smoke bombs. Whatever it is, you now have a proper place to keep track of it. 

Build Materials:

1/4"x6"x2' Red Oak. - $6
Brass hinges-aged - $3 
Round slot head brass screws - $2
Brass corner pieces - $1
Post Screws/ Chicago Screws - $5
Leather FREE- take apart a purse
Glue - Gorilla glue from around the "shop"
Paint - $7 Hammered Copper
Sandpaper - had around the "shop"
Paper to fill. 


Shop Materials:

Drill
Saw
Square
Clamps
Pen/ pencil 
Sharpie/black paint
Brush for glue/ toothpick 
Utility knife/Blade to cut leather
Screwdriver- for assembly/ dis-assembly 

Age Brass:

Sandpaper
Acetone
Vinegar 
Salt

For my design my paper is 5"x7" and the wood is 1/4" bigger on both sides and the bottom, the top is flush with the wood. The actual width of a 6" piece of wood is 5 1/2" so the size was perfect. Just the length needs to be measured drawn and cut.  Draw the hinges, mark the holes.  Also mark the holes for the Posts. I used 3. 

You should have all your cuts and holes marked on the wood at this point. Cut the parts out. For drilling the holes for the hinges I used a rotary tool with bit I did this by hand,  only went through one hole, if you do just fill in, paint will cover. (these are all the parts cut and drilled post paint, wasn't able to cut and drill and hold the camera at the same time.  :)   )   Drill the Post holes. DRY FIT everything BEFORE painting. It makes it all fit better and it's easier to make any adjustments before painting. 

I used Rust-Oleum Universal Hammered Copper and laid it on THICK. In the end a little too thick which is why these paint pictures look much different than the finished product. 

Spray on in thin even layers allowing time to dry between paintings. 

A light sanding between coats will also give a much smoother finish.

We all want that good old Steampunky feeling in our brass, here's how I got mine.

I took SOLID brass hinges/Screws and sanded the protective coating off. Then soaked in acetone , soaked in vinegar and salt, dried off. After the first time you should be able to see the little bits of coating on the brass you missed, sand them off and soak it in vinegar again. I soaked in vinegar for about 15 minutes, let air dry and did it again until it had the color I wanted. 

The corner covers I colored with a black Sharpie and just sanded off, I tried the vinegar soak but it didn't seem to have much results. 

The Screw Posts I did the same with the Sharpie and sanding but I think I am going to do it with black paint and sanding next time.

The brass screws I also cut down as they were longer than the 1/4" piece I was putting them into. 

Now we're ready to put her together.

First you want to install the hinges. After making sure everything dry fits together I put a drop of Gorilla glue in each pre-drilled hinge hole and on the ends of the screws going in there. 

Then I glued and clamped the corner covers on and let the glue dry. 

For this part I just lined up how I wanted the seam to lay on the front, marked where the holes for the screw posts go and laid over the back for the same thing.  

To mark the holes I dry fit the screw posts and held the leather over the top and marked with a Sharpie and then cut with a razor blade. 

After the holes were marked and cut I brushed the ares with glue to keep the fit and look tight and held with clamps until dry. 

After it was dry, I trimmed the overhanging edges with a razor. 

Now you have your very own Captains Log Steambook paper note receptacle!!  These are just pictures of finished details. You can use any paper you want- this is what I could afford for this build and I do a LOT of writing, now it just looks cooler when I do. 

It's my first steam punk project and instructable. So be nice! 

And please rate or vote or whatever we do here!!