Speed Knitted Hoodie

by KirysTouch in Craft > Knitting & Crochet

69 Views, 0 Favorites, 0 Comments

Speed Knitted Hoodie

Speed Knit Hoodie.JPG
FPKKNDGLTLIXXI4.jpg

_As I was late for the 'Instructables Warm' Contest, I decided to create a 'Speed Knitted' Hoodie! So I grabbed a Fluffy Chunky yarn I never had knitted with {cause I live in the Caribbean}, and a regular colorful 4 strand yarn. And Started day & night. 2nd pic. shows the Reversible ver.

Supplies

Ndls etc Used.JPG
2 Yarns.JPG

_Needles needed: A #35 big needle & a pair of #15 ndls.  In 'Speed Knitting', 1 row is knitted with the #35; then the other row with the #15. Also used 2 Crochet ndls.: #N/9.0mm & #H/8-5mm (H used for tying the yarn)

Face Edge to do.JPG
Single Cro Face Edge.JPG
Center Measured.JPG
Finished Measures.JPG
Stockinette Hoodie verion.JPG
Purl Hoodie verion.JPG

~*~*~*~*~~*~*~*~*~~*~*~*~*~~*~*~*~*~~*~*~*~*~

__Ribbing St. - Used is 2x2 [*P2, K2*]. 

__Selvedge is Simple: Start rows passing TBL the 1rst st of the Row [don't knit].  [TBL= thru back loop]

At the end, Knit the Last st. of that same row. Do same on both sides. 

~*~*~*~*~~*~*~*~*~~*~*~*~*~~*~*~*~*~~*~*~*~*~

__I Casted On 18 + 2 Selv. sts. = 20 total.  The Casting On was knitted upon the #35. 

No Pattern was used. I went measuring myself as went along. *[After I finished, found out 12 + 2 would have been perfect.] 

The Ribbing was done with both yarns together. 

> To pass the sts from the #35 ndl to the #15 is easy; but to pass those sts from the #15 to the #35 is slower & tricky as 

the thinner yarn can drop un-noticed. 

> 6 Rows of Rib were knitted. 3 in the #35. Other 3 in the #15. 

Last row will be with #15, take the twin ndle #15 & with both knit a non Rib row. Tie & cut the Color yarn. 

> From now on the knitting is with the Cream color Chunky in Stockinette St. Knit 22 1/2" long. Which is not slow thanks to the #35 ndl. 

> To re-initiate the Ribbing at the other end, invert the order of the steps of the 1rst Rib. 

Ex.:  Tie the Color yarn. First do 2 rows as Stock. St. with the 2 #15's. 

Start the 6 Rows of Rib. Use #35 ndl. 1rst.  Once finished, Cast Off as if Ribbing also for elasticity. 

> Proceed joining method you prefer. Start at front. 

If you want to do Single Cro's around the Face edge, do so loosely using like a #N ndl. 

To make it Reversible, don't use yarn. Use Sewing poly. thread doubled & match Selvedge loops & tie them together, pair by pair.  Good Luck! ..... And "et VOILA"

P.D. #1 If you can't find #35 ndls, make your own!

P.D. #2 This is my 1rst Project. It's not perfect; but remember I'm just Human! ;-)