Skateboard Model

by hpfhpfsuperman in Outside > Skateboarding

305 Views, 0 Favorites, 0 Comments

Skateboard Model

成品2.png

This project mainly introduces the construction process of the author's skateboard

1.png

First, drag out a box, set the length to 90, the width to 30, and the height to 1.

2.png

Drag out a half cylinder, set the diameter to 30, the length to 24.38, and the thickness to 1.

3.png

.Adjust the tilt angle of the half cylinder to 13 ° and copy.

4.png

.Move the copied other half cylinder to the other side of the box and rotate it 180 ° to align and group the three. Set to black after grouping.

6.png

Drag out a box, set its color to gray, and set its length to 26, width to 20, and height to 1.

7.png

Drag out another box, and set its height to 1, length to 20, and width to 15.

8.png

Align the two boxes on the X and Y axes. As shown in the figure. Form wheelbase.

9.png

Drag out 2 cylinders and set the diameter of one of them to 5 and the height to 2.5. The other has a diameter of 2 and a height of 5

11.png

Drag the two cylinders onto the wheel base and align them in the x-axis direction, as shown in the figure.

12.png

Drag out a half cylinder and set its width and diameter to 6.88, height to 1 and length to 15.22.

13.png

Drag out a cylinder with a diameter of 3 and a length of 10.75.

14.png

Connect the cylinder and the half cylinder and align them in the x-axis direction. And group them as shown in the figure.

15.png

Pull out a spring and set it directly to 3, with a height of 4.

16.png

Drag out a box, set its length to 3, width to 2.67, and height to 1. And copy it.

17.png

Connect the two small cuboids to the two sides of phlegm yellow and group them.

18.png
19.png

Drag out 2 triangles, and set one of them to 15 in length and 1 in height, and the other to 20 in height. Copy them once respectively.

20.png

Connect to the wheel base as shown in the figure. And divide them into groups.

21.png

Move the spring structure onto the small thick cylinder and tilt it 3 °.

22.png

The combination of the cylinder and the half cylinder is moved to the place as shown in the figure, and the inclination is 14 ° to connect with the spring structure.

24.png
25.png

Drag out two polyhedrons respectively. Set the diameter of one to 1 and set to hole. The other has a diameter of 3.

26.png

Align the two. And divide them into groups. So a nut is made.

28.png

Set the nut to black and move it as shown. Group as a whole.

轮胎.png

Drag out a sphere, set the length to 6, the height to 6, and the width to 4. Drag out another cylinder with a diameter of 6 and a length of 2.

轮胎2.png

Splice and duplicate the sphere. As shown in the figure. Group and set to black.

轮胎装饰.png

Drag out a ring and set the wall thickness to 1 and the radius to 6.

轮胎装饰3.png

Make the ring coincide with the center of the tire.

轮胎成品.png

Connect the tires to both sides of the axle and group them.

成品侧视图.png

Copy. And connect the main body respectively.

成品3.png

Drag out a small cylinder with a diameter of 1 and a height of 2.5. Copy 7 times. Install as shown.

成品2.png
成品背面.png
成品侧视图.png
成品底下测.png
成品俯视图.png
成品前方.png
成品装饰后1.png

Finally, add a little decoration to the skateboard to make it more beautiful and beautiful.