SECRET BOTTLE

by hdissanayake in Workshop > Organizing

2789 Views, 19 Favorites, 0 Comments

SECRET BOTTLE

DSC08032.JPG

Hello guys. In this Instructable I'm gonna show you how to make a SECRET BOTTLE storage..

So let's get started.

Main Plan

my idea is to make a secret storage by using a small glass bottle.usually people open a bottle by opening the lid. In this case I'm gonna seal the lid & make our own undetectable lid.

Tools & Matterials Needed

DSC00797.JPG
DSC00743.JPG
DSC00809.JPG

Tools::

1. glass cutter

2.gas burner/ candle (for heating purpose)

3.pliers

4.hammer

5.small paint brush

Materials:::

1.small glass bottle(darken glass is better)

2.paper clips

3,epoxy glue

4.nails

5.wood plate (about 4''x4'')

6.sand paper(about grit 180)

7.black paint

Make the Stage for Bottle Cutting

DSC00749.JPG
DSC00750.JPG

i'm gonna use a glass cutter to cut the glass bottle.but this method would not be usual for you all.first step of cutting the bottle is engraving a clean line on the bottom of the glass bottle.for that I use a wooden base to keep the bottle still along the horizontal plane .the wooden base made by hammering two nails on the wooden plate.

NOTE ; when hammering nails make sure that both nails are touch the bottle as show in the figure

Engrave the Bottle

NEW.gif
DSC00751.JPG
DSC00761.JPG

after making the stage we can start engraving the bottle.place your bottle on the stage and hold the glass cutter as shown. then rotate the bottle one time.So its done we've engraved a perfect line(actually a loop).

Finalising the The Cut

DSC00764.JPG
DSC00769.JPG

we got a perfect cut.But how we could separate the bottle apart.Also this is the interesting part.grab the botlte from the top and heat the engraved line care fully. If you are new to this tecuniq I recommend to use a candle as the heating source. If you over heat the bottle you would end up with failed result. Anyway after heating the bottle suddenly drop it in to water(a sudden cooling). if you done correctly it cut the bottle nicely along the line

Sanding the Edges

DSC00775.gif
DSC00783.JPG
DSC00785.JPG

now we have to sand down and make the edges clean.So i use a 180 grit sand paper .place the sand paper on a flat surface and put some water on the paper.do the sanding as shown in the GIF.

Prepair Paper Clis for Locking Mechanism Part : 1

DSC00818.JPG
DSC00810.gif

we've completed cutting and sanding the bottle.Our next step is to make locking mechanism for the lid.I use 4 paper clips for the lock.for each lock i use 2 clips, then i get 2 locks.

Bend the clips as shown in GIF.also you have to generate a curve as shown in the image

this clip is used to place in the lid

Prepair Paper Clis for Locking Mechanism Part:2

DSC00830.gif

Bend the clips as shown in GIF.
this clip is used to place inside the upper bottle part

Making the Lid

DSC08010.JPG
DSC00820.JPG
Untitled-1.jpg

next glue the clips to the lid as shown in the image. also you have to bend it again as shown in image ti sit them perfectly inside the lid.I used epoxy glue.

give good time to cure the glue.

after glue is cured ,then insert the lid in to the upper bottle part.even the bottle is dark you can see through glass. So mark the point outside the bottle as shown in the fig 3

repeat the process for the oposit side.

Upper Part of the Bottle

DSC018013.jpg
DSC08018.gif

now glue the clip we made early as shown in the image. Previously marked mark must be align as shown.

the locking mechanism is now completed.the GIF image shows how the lock look like when its locked.

​darkening the Bottle

DSC08026.JPG
DSC08029.JPG

the main part of the bottle is over.because of the transparancy any body could see stuff hidden inside the bottle.therefor I darkening the bottle by painting black inside of the bottle.

after painting the bottle is tottaly darked.

Finishing

finally we have to seal the old lid of the bottle by glue. So nobody could open the bottle.