Rotating Concrete Lamp From Coke Cans

by theNBstuff in Workshop > Lighting

1672 Views, 14 Favorites, 0 Comments

Rotating Concrete Lamp From Coke Cans

56.png
rotating lamp with concrete base from soda cans

The way the lamp works is based on the physical law of buoyancy discovered by Archimedes. In simple terms, Archimedes's principle states that there's always an upward force pushing on a partially or fully immersed body in a static fluid. It's called buoyancy force. And this force is equal to the weight of the fluid displaced by the body.

When the light bulb is turned on, air inside the can is heated up. The air molecules move faster and away causing density to decrease. Hot air becomes lighter and so is its displacement. It moves upward and escapes through the opening while pushing on the fans/wings on the top causing the can to rotate.

Remove the Top

1.png
2.png
3.png

I just stick sandpaper to a piece of wood using spray adhesive to make sanding easier

Tube to Attach Candelabra Socket

4.png
5.png
6.png
7.5.JPG
7.png

Non-rusted materials such as PVC, brass, stainless steel, etc. are preferred for the attachment. The one I have is 1/2 inch in diameter. The length we need is about 5 inches. It's best for the socket to fit tightly inside so that we don't need to use any glue.

Prep the Base - Tube

8.png
9.png
10.png

Drill a hole large enough for the tube. If you don't have a drill bit big enough, use pliers or anything you can find to make the hole bigger. Push from inside out.

Prep the Base - Legs

11.png
13.png
14.png
    We need 8 bicycle spokes for the legs. Shape them however you want but star bending at least 6 inches away from the J bend on top. Wrap your bending tool with paper+tape to avoid scratching the paint off.

Prep the Base - Top Pole

15.png
16.png
Coke_12oz.png
    This silver bicycle spoke will act like a pole for the top to rest on while it rotates.

Prep the Base - Tube+legs+pole

19.png
18.png
17.png
20.png
21.png
22.png
23.png
    Hot glue tube+legs+pole to the can

Pour the Concrete

24.png
25.png
26.png
27.png

Before pouring, cover the tube so nothing gets inside. We want it to be as clean as possible.

Prep the Top

28.png
31.png
32.png
33.png
34.png
35.png
44.png
    Cut 8 slots on the can...equal spaces between the slots. Shape the slots into "fans" (see last pic). Depend on the way you pry the slots, the can will rotate differently. Mine will rotate from right to left.

    Find the center with a coin then drill a hole and epoxy a pushpin.

The Art of Poking

36.png
37.png
38.png
39.png
40.png
42.png
41.png

Find a piece of art you like, print it out and slap on the can. Note the height of the image can not be higher than 4.25 inches. Use a sewing needle to carefully poke holes along the line art. When done, either spray paint it or sand off the paint if you like the bare aluminum look.

Low Friction Dome and Levelers

45.png
47.png
48.png
49.png
50.png

Make a dome shape using any suitable tool you can find as long as it's not too sharp. The aluminum is quite thin. Epoxy the dome on a "nipple" and screw it onto the silver pole. Screw 8 more on to the legs.

Wiring Up

51.png
52.png
53.png
54.png

Run the cable from the bottom through the tube before wire the leads to the socket. Use heat shrink tube for safety.

Result

55.png
IMAG0055.jpg
IMAG0063.jpg
IMAG0064.jpg

Turn on the light to warm up then put the can with image on top, push pin rests on the dome. It'll start spinning!

THANKS FOR BEING INTERESTED!