Raspberry Pi + Node.js + Blynk App + DHT11/DHT22/AM2302

This time we will display some sensor values (DHT11 in example) on the Smartphone using Blynk App.
You will need:

1. Raspberry Pi with internet connection
2. Temperature and humidity sensors: DHT11 or DHT22 or AM2302
3. Jumper wires

Please check my tutorial about getting Blynk and Node.JS running on Raspberry Pi and other single-board computers (BeagleBone, Intel Edison, Galileo, VoCore, OpenWrt... ):

After you get Blynk JavaScript library running, we can move on to reading sensor values.

For DHT11/DHT22/AM2302 sensors, you need to download and install:

• bcm2835 library

• node-dht-sensor npm package

Here are the commands I run on my Raspberry to do this (it may take some time to execute...):

wget http://www.airspayce.com/mikem/bcm2835/bcm2835-1.46.tar.gz
tar zxvf bcm2835-1.46.tar.gz
cd bcm2835-1.46
./configure
make
sudo make check
sudo make install
sudo npm install -g node-dht-sensor

Note: You may want to read the node-dht-sensor Readme, and run "First Example" ;)

After logging in to the Blynk App, you can scan the QR code and get the project I have prepared for you (only Android, for now...).

Alternatively, you can create it manually:

1. Create a new dashboard of type Generic, and send yourself an Auth Token.
2. Add a Graph widget and bind it to V3
   Set range to 10..40,
   reading frequency to "PUSH"
3. Add a Value Display widget and bind it to V4
4. Press Run (triangle in the upper right corner)

Wire Raspberry Pi and DHT11:

• GND to GND
• sensor Signal to gpio4
• sensor VCC to 3.3v

On the board, create a new file (call it blynk-sensor-test.js):

var blynkLib = require('blynk-library');
var sensorLib = require('node-dht-sensor');

var AUTH = 'YOUR_AUTH_TOKEN';

// Setup Blynk
var blynk = new blynkLib.Blynk(AUTH);

// Setup sensor, exit if failed
var sensorType = 11; // 11 for DHT11, 22 for DHT22 and AM2302
var sensorPin  = 4;  // The GPIO pin number for sensor signal
if (!sensorLib.initialize(sensorType, sensorPin)) {
    console.warn('Failed to initialize sensor');
    process.exit(1);
}

// Automatically update sensor value every 2 seconds
setInterval(function() {
    var readout = sensorLib.read();
    blynk.virtualWrite(3, readout.temperature.toFixed(1));
    blynk.virtualWrite(4, readout.humidity.toFixed(1));
    
    console.log('Temperature:', readout.temperature.toFixed(1) + 'C');
    console.log('Humidity:   ', readout.humidity.toFixed(1)    + '%');
}, 2000);

Replace YOUR_AUTH_TOKEN with your token from the App.
You may also want to change sensorType and sensorPin.

Now run it:

sudo NODE_PATH=/usr/local/lib/node_modules node ./blynk-sensor-test.js

The output should look like this:

OnOff mode
Connecting to TCP: cloud.blynk.cc 8442
Connected
Temperature: 18.0C
Humidity:    26.0%
Temperature: 18.0C
Humidity:    26.0%

Note:

• You need to run our script with sudo as the sensor library requires privileged access to the hardware

• NODE_PATH=.. is set because Node.js may fail to locate global modules otherwise

Now, check the Blynk App on your smartphone, it should display a nice plot of temperature and current value of humidity. Congratulations! ;)