R/C Grinder Gear!
![ripiics 076.jpg](/proxy/?url=https://content.instructables.com/F1J/9BSX/JLFEZ7BCW3Z/F1J9BSXJLFEZ7BCW3Z.jpg&filename=ripiics 076.jpg)
take an old rc helicopter and make a new toy!
i am pretty sure that this can be done with any helicopter that can be taken apart.
i am pretty sure that this can be done with any helicopter that can be taken apart.
Gather Ing the Materials.
![ripiics 070.jpg](/proxy/?url=https://content.instructables.com/FEY/Y0A3/0VLEZ7BCW51/FEYY0A30VLEZ7BCW51.jpg&filename=ripiics 070.jpg)
im sorry if this picture is fuzzy, but my cam sucks.
the materials are;
1.old rc helicopter
(these are from the heli)
2.the battery recharger
3.the rechargable battery
4.the motor(it needs to have a metal gear)
5.the control panel+antenna
6.the remote control(not in pic)
7.electrical tape
the materials are;
1.old rc helicopter
(these are from the heli)
2.the battery recharger
3.the rechargable battery
4.the motor(it needs to have a metal gear)
5.the control panel+antenna
6.the remote control(not in pic)
7.electrical tape
Assembly #1
![ripiics 072.jpg](/proxy/?url=https://content.instructables.com/FXU/IIKG/QZREZ7BCW61/FXUIIKGQZREZ7BCW61.jpg&filename=ripiics 072.jpg)
![ripiics 073.jpg](/proxy/?url=https://content.instructables.com/FY5/O4YO/OKUEZ7BCW72/FY5O4YOOKUEZ7BCW72.jpg&filename=ripiics 073.jpg)
![ripiics 074.jpg](/proxy/?url=https://content.instructables.com/FB6/ZNUH/7COEZ7BCW81/FB6ZNUH7COEZ7BCW81.jpg&filename=ripiics 074.jpg)
take the battery and the control panel and tape them together as shown.
you need to make sure that the 2 plugs can connect after taping.
you need to make sure that the 2 plugs can connect after taping.
Assembly #2
![ripiics 075.jpg](/proxy/?url=https://content.instructables.com/FOJ/6KTG/A7SEZ7BCW8U/FOJ6KTGA7SEZ7BCW8U.jpg&filename=ripiics 075.jpg)
![ripiics 076.jpg](/proxy/?url=https://content.instructables.com/F6L/3E6D/O3PEZ7BCW9J/F6L3E6DO3PEZ7BCW9J.jpg&filename=ripiics 076.jpg)
take the completed battery assembly and the motor. whe n taping these, you neec to be careful not to tape over the heat holes.
after taping , connect the wire from the motor into the slot.
after taping , connect the wire from the motor into the slot.
Finishing Up
![ripiics 076.jpg](/proxy/?url=https://content.instructables.com/F1J/9BSX/JLFEZ7BCW3Z/F1J9BSXJLFEZ7BCW3Z.jpg&filename=ripiics 076.jpg)
first get the antenna and tape it to the side of the control panel
then hook up the battery.
there u go!
then hook up the battery.
there u go!
Using It
![ripiics 077.jpg](/proxy/?url=https://content.instructables.com/FMI/RMOI/9P7EZ7BCWA9/FMIRMOI9P7EZ7BCWA9.jpg&filename=ripiics 077.jpg)
![ripiics 079.jpg](/proxy/?url=https://content.instructables.com/FSH/TTYF/X3TEZ7BCWAZ/FSHTTYFX3TEZ7BCWAZ.jpg&filename=ripiics 079.jpg)
![ripiics 080.jpg](/proxy/?url=https://content.instructables.com/F2Z/8NFE/L0DEZ7BCWIB/F2Z8NFEL0DEZ7BCWIB.jpg&filename=ripiics 080.jpg)
all u need to do is find something to grind,(plastic is best)
turn on the remote control and the grinder, and rev it up!
turn on the remote control and the grinder, and rev it up!