How to Make the 007 Desk

Hello everyone, in this project i will show you how to transfer or recycle cartoon and paper in a useful way. I have been a long time planning for an overdesk to help me in studying and creating until i found the perfect design which is as i will show you here in my instructable step by step. This overdesk contains spot light (lamps) , fan, speakers and a secret boxes for hiding top secret objects for you.

NOTE: THIS PROJECT IS TOTALLY MADE OUT OF CARTOON EXCEPT THE ELECTRIC CIRCUIT.

Here I present the final look of my project.

Simple cartoon papers and an right angled one.

• glue gun
• scissor
• blade
• marker and a pencil
• white glue
• scotch
• ruler
• drill

• Screwdriver

• Screws

• spray paint

• electric tube

• THE UPPER PART: 30cm on the straight part and 15cm on the inclined part and 15cm on the rear side with width=40cm.
• THE LOWER PART: L=75cm W=40cm (length and width)

Cut it as A4 size

• Size: L=30cm W=22cm
• cut two rectangles with L=30cm W=3cm and another one but with L=15cm
• add at each terminal an 1cm square
• paint it with a spray

cut the lower part as what you need to put in your overdesk, lamps, speakers......

and paint it

fit the lamps in a way that can be convenient with your desk (distribute the spot lights).

• cut the a rectangle with length L=40cm and width W=8cm
• cut another rectangle with L=40cm and W=16cm
• cut a square with a=8cm

Gather the parts of the box using a glue gun.

• Form using an paper scotch the word that you need to spray it.
• be careful to insulate the letters well.
• paint it.

• After painting the box try to get off the tapes that form the word "Top Secret".

• using a spray paint the whole project.
• try to make some decorative waves or any drawing to not make it classic or regular.

Using a glue gun and scotch tape stick the right angled cartoon to the upper part to give it strength.

Drill two holes to fix the overdesk using screws.

• balance the upper part to be straight
• setup the upper part using a screw driver and a screw.

• use a small box for the control panel (here I used my smart watch box)
• cut the small box according to the number of switches you may put.

• put each switch in it convenient place
• paint the box using a spray

• In wiring you will use the lamps, wires, switches,soldering....

• each component in this circuit is connected in parallel
• all of the circuit is connected to a 6V battery.

• connect each switch to its convenient lamp
• first there is two switches for the two lamps
• and another one for the fan
• additionally to the wire AMF for speakers
• all of that is connected directly to the overdesk using an electric tube

• place the lamps closely to each other and glue them up
• place the fan and the speakers, then glue them
• here the speakers are connected separately to the control panel
• connect the negative wire of the two lamps and the fan together and connect it to the battery

• extend the positive wires from the lamps and the fan separately to the control panel.

NOTE: THE LAMPS AND THE FAN ARE CONNECTED IN PARALLEL

• pick a bright color like blue or red for the emergency lamp
• place beside the other lamps and glue it up.

ROLE OF THE EMERGENCY LAMP: In the case of battery low or the loss of electricity,then there is an alternative lamp that you can use it in this cases.

• after wiring the circuit you are ready to setup the lower part
• using a glue gun and scotch tape stick up the lower part complementary to the upper one on the wall.

• Fix the wires connected in the overdesk from the electric components to the control panel.
• fix them to the lower part.

• Gather all the wires in an electric tube by putting them in it.
• by putting them in the electric tube it will decorate the view of wires.

• after wiring add the lower part to the upper one by gluing them together.
• to be easier for you, use a tape to keep it fixed and then glue them together.

• add some wooden sticks between the upper part and the lower one.
• this prevent the deformation of the setup.

decorate using a nice ribbon to hide the glued part.

• test the lamps, speakers and the fan.
• be careful to check them up before finishing it completely.

• using wooden sticks cut two pairs of 2cm per peace.
• add them to the box paper at the center of each side in a right angled form.

• glue the form shown in the picture to the stick.
• be sure to make it convenient to the stick from the box paper.(the switch)

• add a cubic cartoon cap to the stick of the lock.
• it give it a decorative view.

• glue the both of the part sides of the overdesk to the other parts.
• cut a small place in these parts for the lock after connect it to the lock inside it.

add the box paper to the whole system.

before get up the hidden boxes or the secret boxes.

after showing the secret boxes.

these two steps will be explained in the video.

FINISHED!!!!