Paracord Lanyard
![temp_1614624700.jpg](/proxy/?url=https://content.instructables.com/FS4/RR6G/I4O23UUO/FS4RR6GI4O23UUO.jpg&filename=temp_1614624700.jpg)
![temp_860501531.jpg](/proxy/?url=https://content.instructables.com/F2G/KHWO/I4O23UXJ/F2GKHWOI4O23UXJ.jpg&filename=temp_860501531.jpg)
![temp_1430272493.jpg](/proxy/?url=https://content.instructables.com/F93/EV6N/I4O23V02/F93EV6NI4O23V02.jpg&filename=temp_1430272493.jpg)
For this lanyard a few supplies are needed. Required supplies are paracord (8 feet of each color if you choose to do two) a buckle (the bigger the better) last but not least a keychain clip/ key ring. you will also need a knife/strong scissors and a lighter. NOTE: the nuts are optional for different kind of look.
Getting Started
![temp_1144196623.jpg](/proxy/?url=https://content.instructables.com/FHT/LF9Q/I4O23V2L/FHTLF9QI4O23V2L.jpg&filename=temp_1144196623.jpg)
![temp_-1571696601.jpg](/proxy/?url=https://content.instructables.com/FJI/WSOW/I4O23V3Z/FJIWSOWI4O23V3Z.jpg&filename=temp_-1571696601.jpg)
you want to start off by doing a cobra stitch pattern. if you dont know how to do the cobra stitch its just a simple over under pattern. i did this for about 3 1/2 inches.
Bottom Portion
![temp_-817816975.jpg](/proxy/?url=https://content.instructables.com/F0M/2TI8/I4O23V5D/F0M2TI8I4O23V5D.jpg&filename=temp_-817816975.jpg)
![temp_357614985.jpg](/proxy/?url=https://content.instructables.com/FPN/RF9Y/I4O23V8E/FPNRF9YI4O23V8E.jpg&filename=temp_357614985.jpg)
![temp_1511177031.jpg](/proxy/?url=https://content.instructables.com/F6B/88JC/I4O23VBE/F6B88JCI4O23VBE.jpg&filename=temp_1511177031.jpg)
the bottom portion is basically the same as the top accept you add in the shackle or keychain clip/ key ring.
2nd Layer of Paracord
![temp_2084757731.jpg](/proxy/?url=https://content.instructables.com/FJ5/X6P9/I4O23VBT/FJ5X6P9I4O23VBT.jpg&filename=temp_2084757731.jpg)
![temp_-176263247.jpg](/proxy/?url=https://content.instructables.com/FZJ/CKJR/I4O23VCU/FZJCKJRI4O23VCU.jpg&filename=temp_-176263247.jpg)
for this you just repeat the process of cobra stitching over the first layer.
Finished Product.
![temp_940756400.jpg](/proxy/?url=https://content.instructables.com/F2O/5K7Y/I4O23VGI/F2O5K7YI4O23VGI.jpg&filename=temp_940756400.jpg)
![temp_1264227889.jpg](/proxy/?url=https://content.instructables.com/F08/GJNA/I4O23VJ0/F08GJNAI4O23VJ0.jpg&filename=temp_1264227889.jpg)
![temp_-912928219.jpg](/proxy/?url=https://content.instructables.com/FXN/TIJR/I4O23VJY/FXNTIJRI4O23VJY.jpg&filename=temp_-912928219.jpg)
![temp_-475790527.jpg](/proxy/?url=https://content.instructables.com/FF9/3Q4H/I4ORJJER/FF93Q4HI4ORJJER.jpg&filename=temp_-475790527.jpg)
once you have finished you can put your id and keys on it. just a nother simple project in the books.