Mini Plane Ride
![3E0D30D6-FAB8-4359-89ED-6C69A9C7400C.jpeg](/proxy/?url=https://content.instructables.com/FW3/304J/KEIYMRHJ/FW3304JKEIYMRHJ.jpg&filename=3E0D30D6-FAB8-4359-89ED-6C69A9C7400C.jpeg)
Body of Ride
![Ride 1.PNG](/proxy/?url=https://content.instructables.com/FPR/6Y5F/KEH3W03M/FPR6Y5FKEH3W03M.png&filename=Ride 1.PNG)
![Ride 2.PNG](/proxy/?url=https://content.instructables.com/F4G/6R2B/KEH3W03L/F4G6R2BKEH3W03L.png&filename=Ride 2.PNG)
Make a cylinder at 98mm by 98mm by 1mm. Then make a room for the motor to go in. Now align the two pieces together and that piece is done.
Beams
![Ride 3.PNG](/proxy/?url=https://content.instructables.com/FA4/04Q3/KEH3W030/FA404Q3KEH3W030.png&filename=Ride 3.PNG)
This step you will need a box sized at 5mm by 80mm by 2mm. Then rotate it to make as many ride things this project will have (From 2-Infinity). In the very center of this you will need a whole to put the motor through.
Riding Part
![Ride 5.PNG](/proxy/?url=https://content.instructables.com/FLR/5H3D/KEH3W00U/FLR5H3DKEH3W00U.png&filename=Ride 5.PNG)
![Ride 4.PNG](/proxy/?url=https://content.instructables.com/FSB/QKKN/KEH3W00X/FSBQKKNKEH3W00X.png&filename=Ride 4.PNG)
Now you can design a plane or something that your mini people can ride in. Whatever you decide for your ride, please post what you did in the comments below.
3D Print
![Ride 6.PNG](/proxy/?url=https://content.instructables.com/FDP/THIZ/KEH3W4X4/FDPTHIZKEH3W4X4.png&filename=Ride 6.PNG)
![5725A095-C96B-4459-AB4F-F0AC0F229C26.jpeg](/proxy/?url=https://content.instructables.com/FYC/9OND/KEIJAS66/FYC9ONDKEIJAS66.jpg&filename=5725A095-C96B-4459-AB4F-F0AC0F229C26.jpeg)
![80142907-77B7-40CA-84AA-EE59E0F675C2.jpeg](/proxy/?url=https://content.instructables.com/FSK/8GBR/KEIJAS6F/FSK8GBRKEIJAS6F.jpg&filename=80142907-77B7-40CA-84AA-EE59E0F675C2.jpeg)
Take your parts and export them to a slicing software. Now print your parts. They should only take about two hours to print.
Start Build
![image.jpg](/proxy/?url=https://content.instructables.com/FSM/GFXQ/KEIJAS6W/FSMGFXQKEIJAS6W.jpg&filename=image.jpg)
Start laying out your parts. You should have; 6 printed parts, wires, motor, motor holder, battery holder, vehicles/people, heat shrink, hot glue, a switch, a paper clip, and a soldering iron.
Build Part 1
![8867B33A-089C-4A51-AD6E-3DD35348D65A.jpeg](/proxy/?url=https://content.instructables.com/FZ7/KGEX/KEIYMR9O/FZ7KGEXKEIYMR9O.jpg&filename=8867B33A-089C-4A51-AD6E-3DD35348D65A.jpeg)
Get your battery holder out and cut and splice the red wire in the middle. Attach the switch to the red wire where you cut it.
Build Part 2
![BC4A9318-16A9-4EEF-9E7E-51B4388486F0.jpeg](/proxy/?url=https://content.instructables.com/FSS/M4FB/KEIYMR7W/FSSM4FBKEIYMR7W.jpg&filename=BC4A9318-16A9-4EEF-9E7E-51B4388486F0.jpeg)
Now solder the red and black wires onto the motor.
Build Part 3
![4C67EDAE-3BF0-44A9-9CEE-66503B4FD30B.jpeg](/proxy/?url=https://content.instructables.com/FBN/Z4YT/KEIYMR8N/FBNZ4YTKEIYMR8N.jpg&filename=4C67EDAE-3BF0-44A9-9CEE-66503B4FD30B.jpeg)
![E387522C-3527-410E-AA2C-AAF6EA7B0EB0.jpeg](/proxy/?url=https://content.instructables.com/F33/5IB3/KEIJAVMJ/F335IB3KEIJAVMJ.jpg&filename=E387522C-3527-410E-AA2C-AAF6EA7B0EB0.jpeg)
Put the motor in the motor holder. Put the motor where it is going to be and hot glue it into place.
Build Part 4
![7C9F0DE4-6E0F-4FEA-BE70-E52E53D8D619.jpeg](/proxy/?url=https://content.instructables.com/FA9/1N0V/KEIYMRCL/FA91N0VKEIYMRCL.jpg&filename=7C9F0DE4-6E0F-4FEA-BE70-E52E53D8D619.jpeg)
![7984810D-1C4E-4C1F-BF46-B9D9B3A2CED6.jpeg](/proxy/?url=https://content.instructables.com/FFV/RSCO/KEIYMRAT/FFVRSCOKEIYMRAT.jpg&filename=7984810D-1C4E-4C1F-BF46-B9D9B3A2CED6.jpeg)
Get the paperclip and cut it to about 3cm long. Put one end of the paperclip in a airplane and the other end on the beam as shown in the pics above.
Build Part 5
![88F285CC-46AE-4745-AD26-4FCF6EA2D894.jpeg](/proxy/?url=https://content.instructables.com/FKA/AR3E/KEIYMR92/FKAAR3EKEIYMR92.jpg&filename=88F285CC-46AE-4745-AD26-4FCF6EA2D894.jpeg)
If the whole that goes on the motor is to big, get paint out and put a bit of paint in the whole to make it a bit smaller.
Ta-Da!
![3E0D30D6-FAB8-4359-89ED-6C69A9C7400C.jpeg](/proxy/?url=https://content.instructables.com/FW3/304J/KEIYMRHJ/FW3304JKEIYMRHJ.jpg&filename=3E0D30D6-FAB8-4359-89ED-6C69A9C7400C.jpeg)
Now put the pieces together and you are done. Sorry about all of the people laying on the ground in the pic.