EL Wire Lighting Up to Sound

by kh12 in Circuits > Wearables

3826 Views, 17 Favorites, 0 Comments

EL Wire Lighting Up to Sound

P1030260.JPG
For this instructables project, I thought I would take an audio sensor, EL Wire and a jacket and have the EL wire form an (A) for Alabama. The goal for the project: I want the EL wire to light up when someone made noises.

Below is a video of a demonstration of the EL wire A blinking when I make sound.



ELwired Jacket

P1030208.JPG
MKSP11-2.jpg
dfrobot-sound-sensor.jpg
P1030217.JPG
P1030169.JPG
P1030170.JPG
P1030144.JPG
P1030264.JPG
EL wire starter 
Relay
Arduino
Audio sound sensor
Jacket
Heat-n-Bond
Liquid Stitch Glue
Pure Color ribbin (black)
Inverter
8x AA battery 
Velcro
Fabric
Needle
Thread

Step 1: Sowing Arduino and Audio Sound Sensor to Jacket

P1030022.JPG
P1030029.JPG
P1030038.JPG
P1030040.JPG
P1030051.JPG
P1030052.JPG
P1030053.JPG
P1030058.JPG
P1030111.JPG
P1030119.JPG
P1030126.JPG
First, I cut a hole down one side of jacket (AKA inside) and I sewed the sound sensor to the collar of the jacket with needle and thread. Then I did the same with the arduino, but I put it inside the hole I made.

Step 2: Make Templates With the Fabric

P1030127.JPG
P1030131.JPG
P1030135.JPG
P1030136.JPG
 I do recommend you drawing and cutting out templates on paper before cut the fabric

First I made templates out of paper and put the templates on the fabric. I cut the fabric into each of the paper shape templates… 


Step Three: Ironing on the Cut Fabric With Heat-n-Bond

P1030162.JPG
P1030164.JPG
P1030139.JPG
P1030156.JPG
P1030151.JPG
P1030154.JPG
P1030155.JPG
P1030147.JPG
P1030160.JPG
P1030157.JPG
P1030137.JPG
P1030165.JPG
P1030166.JPG
I took the Heat-n-Bond Hem tape and placed pieces on the jacket were I was going to put the fabric. Once I laid the fabric over the Heat-n-Bond, I took my iron and placed it on top of the fabric. I let the iron set for 20 seconds. (count 1,2,3…20) For where the buttons are, I split the fabric down the middle. Once I put down the Heat-n-Bond and fabric, I wouldn’t cover the buttons.

Step 4: Adding Black Ribbon to Jacket

P1030172.JPG
P1030173.JPG
P1030176.JPG
P1030177.JPG
P1030178.JPG
P1030179.JPG
P1030181.JPG
P1030182.JPG
P1030174.JPG
P1030185.JPG
I added black ribbon on the ends of the fabric pieces on the jacket for looks and to protect the ends of the fabric from ripping/tearing ex. I recommending you gluing and lying down the ribbon a little bit at a time and let the glue dry for 30 minutes or so before continuing with gluing and lying ribbon down.

Step 5: Hook Up the Components. Inverter, Relay, and Battery

Scan.jpeg
P1030217.JPG
P1030227.JPG
P1030228.JPG
P1030239.JPG
P1030229.JPG
P1030233.JPG
P1030236.JPG
I bought an inverter and a 8x AA battery holder. I connected each piece accordingly. Look at the drawing, this shows how I connected everything. 

Last Step: Sowing on the EL Wire to Jacket

P1030245.JPG
P1030249.JPG
P1030255.JPG
P1030256.JPG
P1030260.JPG
So I finally get to sew on the el wire, and this was frustrating process. My first attempt, I sewed only certain areas to hold the shape in place. What I came across was that the wire was moving out of its shape. (I unpinned areas before I sewed) For instance, like the thread wasn't tight enough. Man was this giving me problems… I ended up not liking how it turned out. I unstitched it and moved the wire some to change the look. Man was that a mistake. So I repined the whole thing. By this time, the shape is completely out-of-wack. So, I ended up leaving the A wacky. 

I guess the lesson learned is if you pin the wire to jacket or something, don't unpin anything until you are done sowing. That was the biggest thing I should've not done. I had unpinned an area I was going to sew and that's how the wire got out-of-wack…. When I was moving the jacket back and forth, the wire was bending and moving….  PIN AND DON'T REMOVE PIN UNTIL YOU ARE DONE SEWING.