Make Home Energy Improvements and Have the Government Pay You Back

Many energy improvements pay for themselves over a period of a few years. The reduced rates that the improvements pass on to you in annual savings should be enough incentive to make the change when possible. But what if you could get someone else to reimburse you for all or part of the improvements? Many areas in the United States offer incentives to home owners to improve the energy efficiency of their homes.

Energy improvements help more than your monthly utility bill. The environmental implications of making changes like these are significant as well.

Before you do anything you should see what programs cover your area, demographic, or circumstances.

In most cases you'll need to own the home that you're making the improvements to. If you're a renter consider talking to the property owner about the improvements. Perhaps you can negotiate a trade by doing some of the labor if they buy the materials. They can knock your rent down in exchange for the work, you get lower utility bills and when they advertise to the next tenant they can brag about those lower utility rates and the energy efficiency.

The Database of State Incentives for Renewables & Efficienc is a great place to start in the U.S. Canada has an energy efficiency program for those using the Canada Mortgage and Housing Corporation or check out the ecoENERGY retrofit program for making improvements to your home.

There is a wide variety of programs available. Everything from local utility companies offering rebates for the purchase of compact fluorescent light bulbs to federal tax credits for the purchase of a vehicle that uses alternative energy.

Once you have found a program on the DSIRE site then make sure the information is up to date by contacting the agency or checking their website.

You can go through your home and evaluate your energy efficiency. It shouldn't be difficult to find areas that should be sealed, or note where insulation is lacking or insufficient. Check out the U.S. Department of Energy's guide to DIY energy audits.

Some programs require a certified audit before and after your improvements to provide a measurable outcome from the improvements. A home energy rating certificate will need to be submitted to show the existing energy efficiency, then you make the improvements (or pay someone to make them), finally you have another audit completed. If you make the required improvements then you can submit for reimbursement for your expenses.

Use the recommendations from your energy audit to make improvements to your home. Keep receipts for all materials and labor for reimbursement.

Chances are pretty good that the improvements you will need to make will largely involve insulation and sealing air leaks.

I have taken advantage of two different programs for two different houses in the last 9 years. The first we put insulation in the floor and attic and sealed gaps and earned a lower interest rate on the loan. The interest rate reduction was significant enough that within three years the interest rate alone made up for the cost of the materials (we did the work ourselves). The improved energy savings probably bumped the break even point to just one year.

Recently, I qualified for up to $5,500 in reimbursement for my current home. The recommendations primarily included adding insulation to the attic and the crawlspace. I paid a few friends $10 an hour to help me get the work done but that expense was not reimbursable. (Strange that if i had contracted the work out entirely those costs would be reimbursable - paying some friends a few hundred dollars probably saved the state thousands.) But with the saved expenses i'm able to make even more improvements to the house that will save me money over the long run.

Adding weather stripping o windows and doors is one of the least expensive and yet effective measures that can be taken to improve energy efficiency.

Sealing openings in the floor, crawlspace or basement wall, and other areas will also help. A bit of fiberglass insulation works well for very large openings. Expanding foam works for small holes. Caulk for even smaller rifts. And finally tape can be used to make sure air isn't transferring.

Working with fiberglass batts is itchy ad uncomfortable work. But when you buy your insulation you can make sure it is the right thickness, width and facing for the job. With the rigid insulation some does come with foil facing, and you can choose the thickness, but you can't order so that it fits perfectly.

I found the following tricks handy for measuring and cutting rigid insulation.

First, have a friend or two to help you. Cutting is best done where you don't have the space and mobility limitations of a crawl space.

Measure the height from the ground to the floor or the bottom of the joist. Measure that height to cut a four foot piece of the material. You can set the tape measure to the desired length and then lock it. Use the casing of the tape measure to slide along the outside of the foam and the hook part of the tape measure to score into the foam. Use that line to cut on.

I found that a reciprocating saw with a long blade worked well for cutting the sheets. It did leave foam sawdust everywhere though!

Hot air rises. And as it does it draws in cooler air to replace the air that has risen. Think of the house as a big chimney. Where does that air come from? A good portion of it comes from below the house. Even when cooling a house, hot humid air from below is introduced to the living space.

An important method of improving air quality in the home is to add a vapor barrier. This step is not likely to be covered in energy efficiency programs but it makes sense to take it on while you're under the house and improving the value of your property.

An increasing practice in construction is to insulate the walls of a crawl space instead of between the floor joists. This allows the area under the house to safely contain plumbing without fear of freezing. Un-vented and "conditioned" crawl spaces result in better moisture control in the home. Overlap the layers of vapor barrier and then tape the seams. Duct tape probably will not work - you should fork out the big money for a tape designed for the purpose.

Most parts of the house you do not have access to add insulation. If you have vaulted ceilings then you might only be able to add insulation under your home. If you have no insulation in the walls seek a professional to have insulation blown in between the studs (presuming you don't want to overhaul the sheetrock).

But fortunately we generally have easy access to our basement or crawl space walls. Check out the EERE guide to crawlspace insulation and determine the best option for your situation.

Add as much insulation as you can afford. Cutting 4 inch thick rigid insulation will take just as long as 2 inch but provides twice the R value. It will cost twice as much though!

If you use rigid insulation, along two of the walls you will have to butt the foam boards up to the floor joists. You will need to fill between the joists with fiberglass batts or with pieces of rigid insulation friction fit into the openings. Be sure to seal any openings or gaps around the blocking.

If you have some insulation in your attic already you can buy unfaced fiberglass batts that you can lay at a 90 degree angle to the existing insulation. In my case, there was R11 insulation between the 2x6 joists. I decided that the resulting "wave" would not give as thorough a blanket as adding directly on top of the R11. I added R38 and took care to keep gaps between pieces to a minimum.

Remember to wear proper protective equipment when working with fiberglass insulation. and try to keep all of your weight on the joists - or use planks on top of the joists to keep from going through the drywall.

Obviously there are other things which might be recommended for your audit. replacing windows, water heaters, and even a more efficient heating or cooling system might be in order. Make sure that your improvements meet the requirements of the program.

Determine how much the energy efficiency has improved for the home by conducting another energy audit. By installing insulation with the markings visible you ensure a faster and more accurate audit.

Follow the documentation provided by the agency for your reimbursement.

Bask in your warmer (or cooler), more energy efficient, less carbon producing pad!