LilCubey - a 3d Printable MATX Acrylic Cube Pc Case

This is a nice-looking, 3d printable pc case designed to stand out. The sharp corners and plexiglas give it a modern, futuristic and eye-catching appearance. Another great thing about the design is it only need a 180 x 180mm bed to be printed.

The airflow is also designed optimaly where the gpu and cpu manage to stay cool even on the most intense benchmarks.

Pc case features:

310mm GPU

205mm CPU Cooler / Single fan AIO

5 x 120mm Fans

SFX PSU

MicroATX/MiniITX

1 Slot for SATA SSD

Also alternatively to the writen guide with images below I recommend checking out this assembly video

For the tools you need:

1. Soldering iron
2. Screw driver
3. Hot glue gun
4. Drill

For the materials:

1. 3-5 kg of filament (any color)
2. Pack of m3 heated inserts
3. Pack of m3 screws
4. Pack of PC screws
5. 3 plexi glas sheets (336 x 336 x 4)
6. 16mm button

3d printing the parts!

I personally used PETG and 15% infill, but higher infill will also work great.

These are all the parts you need to print:

(You can also check out the thingiverse)

Assembling the pc case!

You need 7 heat inserts for this step.

Just Insert the heat inserts like on the images.

First insert 1234Connector

Second slide in 3 and 2DownPart

Third, connect parts by inserting 4 LilConnectors

You need 7 heat inserts for the parts.

Insert the heat inserts exactly like on the images.

First slide through 6 and 5 MotherboardPiece

Second put MotherboardPieceAttacher into parts

Third, slide in 7 and 8 MotherboardPiece

Fourth, insert 4 LilConnectors

If your planning to use a SATA SSD, i recomend sliding it in and screwing it in.

You need 11 heat inserts for this

Just some normal heat inserting like before

First slide in 9 and 10 BackPart

Second, slide in BackPartConnector

Third, insert the 16 mm button into the hole on 11BackPart

Fourth, slide in the 11 and 12 BackPart and insert 4 LilConnectors

You need 10 heat inserts for these parts

Nothing unusual, just heat inserting

You will need 12 m3 8mm screws with 12 nuts

Before screwing in, screw in a nut fully into the screw. Then screw into pc case. Do that for all parts.

You need 9 m3 8mm screws with 9 nuts

First take your SFX Power Supply, 18IoMotherboardPart and screw it in

Second, take the newly screwed in IoMotherboardPart and insert it into the pc case and screw it in

Third, take 19IoMotherboardPart and screw it in

You'll need 4 120mm fans + 8 fan screws for this

Place in the 120mm fans and screw it in only where the image shows

You need 6 Standoffs + Motherboard screws and your motherboard (with cpu fan, ram and etc obviously installed in)

First Screw in the standoffs

Second insert and screw in the motherboard using as many motherboard screws you need

Third, Dont forget the Io Shield!

You need 4 heat inserts

Insert all heat inserts Into 21MotherboardPiece

You need 2 m3 8mm screws, 2 nuts, 1 120mm fan/AIO cpu cooler fan, screws for the fan/AIO and 3 LilConnectors

First screw in 20MotherboardIoPart

Second put in 3 LilConnectors into where shown

Third install your fan/AIO with whatever screws you need

You'll need 4 m3 8mm screws, 2 LilConnectors and 2 heat inserts

First screw in 20TopMbnBackConnector

Second screw in 21TopMbnBackConnector

Third insert 2 LilConnectors

Fourth insert 2 Heat inserts as shown

You need 2 heat inserts and 2 LilConnectors

First take 24Longthing and insert in 2 heat inserts

Second position 24 and 25Longthing and attach 2 LilConnectors

You need 2 ExtraFrontConnectors and 4 fan screws

Place the ExtraFrontConnectors and screw it in with the fan screws

You need 4 m3 8mm screws

Grab 24 and 25LongThing, place it and screw it in

You'll need 2 heat inserts, a GPU and 2 m3 screws (any lenght that works)

First insert in 2 heat inserts (or more depending on your setup)

Second, inserts in your beautiful GPU

Third, Screw in the GPU with the m3 screws

You only need 1 heat inserts for this

Just insert the 1 heat insert

You'll need 8 m3 8mm screws and nuts

Place the Plexiplug'sA and then screw in

You'll need 8 heat inserts

First place the PlexiPlug'sB in

Second place the PlexiPlug'sB in

Third, add 4 heat inserts

Fourth, add 4 heat inserts

For the pc case to be complete 3 336 x 336 mm plexi panels are needed. Each with 4 holes on the corners.

You need to drill 4 holes per plexi glas as show on the images on every corner.

You need 12 m3 6mm screws with nuts

First attach PlexiPlug'sC onto the pc case and screw it in. Do the exact same for all other panels.

I recomend using hot glue for this.

Attach the PlexiPlugs'D onto the PlexiPlug's and use some hot glue in beetween

Now you've completed your cool-looking pc case, go ahead and enjoy it!

(Check out my channel for other cool 3d printable pc cases)