Lego Space HoverCraft

This is a space hover craft I built.
Please read the whole instructable and if you have a question or comment, post it in the comment section.

Parts You'll Need

You'll need a lot of pieces. Some of them are not Lego, for example the grey hood, is some different type of Lego bricks.

Connect the 4/6 Flat Plate to the 4/4&2 Slanted Brick

This is the base of the rocket, from here you'll attach everything to here.
Connect The 4/6 Flat Plate To The 4/4&2 Slanted Brick, or the different variations of bricks you have.

1/4 at the End

You are now going to add one 1/4 brick to the end of the ship.

1/1 on Each End

Your now going to attach a 1/1 plate at both ends of the 1/4 brick.

Add on Two Slated Bricks

On top of each 1/1 your going to attach a 1/2 slanted brick to the ship. It has to attach to the end/s/ of the 1/4, and on the bottom, to the 1/1.

2/2 to Empty Space

You now have to simply attach a 2/2, to the gap created by the two 1/2 slanted bricks on the 1/4 brick. Make sure half of it hangs out over the edge of the space ship.

Smoothen It Out

Your now going to attach two 1/2 FLAT tiles to the 1/4 gap made by the 1/2 slanted bricks.

And add a 1/2 tile to the 1/2 hanging of the end of your ship.

Add a Second 1/4 Beside the Other One

Now, put a second 1/4 brick beside the first 1/4 brick.

Add Two 1/2 on the Middle of the 1/4

Now just add two 1/2 tiles to the middle on top of each other of the 1/4 brick you just added.

Add the Tail Wing

Now just simply add a tail to 2/3 at the back of the ship.

1/1 Slanted Brick on the Two Sides of 1/4

Now your going to add two different / preferably red and blue/ on both ends on the second 1/4 brick.

Add a "seat"

I chose to add this type of "seat" but you can do whatever you want.

Add Two Fences

Now add two fences on the ship.
It should be perpendicular to the second 1/4 brick.

Add a Stealing Wheel

Put a steering wheel perpendicular to the two fences. Their should be a 2/2 "hole" in the middle for a mini figure.

Now Add a 2/2 & 2/3

Now your going to add a 2/2 plate and a 2/3 plate in front of the steering wheel.

1/2 on Top of a 2/2 on a 2/2

Now add a 2/2 on top of the other 2/2. Once the 2/2 / 2 high / is done, put a 1/2 on top of the 2/2, but make sure that you put it as close as you can to the steering wheel.

Add Two Grids

Now add two grids to the 1/2 by the steering wheel and the 1/2 below.

Add Hub Cap

Now add any hub cap you want, I liked this and decided to put it on, but hey it's a free countries, do what you want.

Add Two Wings.

Now your going to add two 2/4 plates on each side of the very first 2/4 holding the base of the ship together. The wings will hold the weapons.

1/1 and a 1/1 With Hook

Add a 1/1 to a 1/1 with a horizontal hook. Make sure the hook is on top.

Gun Holder 1

As you can see in the picture, your going to add it close to the front of the ship, but toward the middle/ on the 2/2 wing BTW/

Add Gun/ Camera

Now add the camera/ rpg to the horizontal hook on the wing.

Adding Gun No. 2

Now your going to take a 1/2 with 1/2 studs on each side including the top and front, with a nozzle at the back

Finishing Gun No. 2

Now on the front of the block on the wing, there is a stud, that's where your going to your 1/1 cylinder brick.

Add the Turbo Engines

Now on the bottom of the space ship, you are going to put 3 turbo engines on the areas on the picture

Starting Guns No. 3&4

Now take the brick with the guns on a 2/2 piece.

Add Two Technic Pins

Now add a Lego technic pin on each gun.

Add Two Technic Cylinders

Now add two Lego technic cylinders to the pins on the guns.

Finishing the Guns.

Now add a 1/1 orange coloured plate to the technic cylinder.

Add Them to the Front of the Ship

Now just add the guns to the front of the ship, underneath the base plate would be preferable.

Wing Touches

Now your going to add a 1/2 and a 1/4 to the ship, try to have the 1/2 be a flat tile and put it on the front on the tail wing.

Add the 1/4

Add the 1/4 plate to the back of the tail wing.

Add the 1/2

Now add the flat tile 1/2 to the front of the ship.

That's It!

That's it, that's how you build the hovercraft. Please leave a rating or a comment. Thanks for reading this instructable.

Bye