K'nex Tower Crane

by MrSmashCat in Living > LEGO & K'NEX

31221 Views, 21 Favorites, 0 Comments

K'nex Tower Crane

IMG_9561.JPG
Here is a tower crane I made one weekend that is about 75 inches (6.25 feet) tall. It has almost every function off a real tower crane. It can rotate 360 degrees, the trolley moves from the tip of the jib, all the way back to the tower, and the hook can lower all the way to the ground no matter where the trolley is. Even though the crane can only lift a few ounces, it was a build that I really enjoyed, and (if you have the pieces), I hope you will build and enjoy too! Please rate and comment! :D

Pieces Count

This tower crane is very large and uses MANY pieces, so it would be a really good idea to make sure that you have all the pieces before you start building. Note that the count may not be 100% perfect, but should be very accurate.

Connecters:
Gray (1 slot): 3
Gray (2 slot): 6
Orange: 142
Red: 17 
Green: 6
Yellow: 29
Silver Slide: 272
Blue Slide: 52
White Circle: 43

Bars/Rods:
Green: 154
White: 131
Blue: 238
Yellow: 259
Red: 151
Gray: 13

Other:
Brown/Tan Clip: 13
Blue Clip: 36
Black Hinge: 4
Blue Spacer: 50
Silver Spacer: 105
Micro Chain Gear (Black): 4
Micro Gear: 2
Large Gear: 1
Medium Gear: 2
Small Gear: 1
Big Wheel: 5
Big Tire: 0
Small Wheel: 4
Small Tire: 4
Motor: 3
Chain Links: 162
String: 20-25 feet
Marbles (optional): 70-90 (depending on size of load)

The Base

IMG_9588.JPG
IMG_9590.JPG
IMG_9591.JPG
IMG_9592.JPG
IMG_9593.JPG
IMG_9594.JPG
IMG_9595.JPG
IMG_9597.JPG
IMG_9598.JPG
This is one of the easiest sections to build, although it could be considered the most important. 

The Tower

IMG_9600.JPG
IMG_9601.JPG
IMG_9602.JPG
IMG_9603.JPG
Okay, I lied, this is the easiest section of the crane to build :)This part attaches to the base to hold up the jib and counter weight.

The Rotating Mechanism

IMG_9606.JPG
IMG_9611.JPG
IMG_9612.JPG
IMG_9613.JPG
IMG_9614.JPG
IMG_9616.JPG
IMG_9617.JPG
IMG_9619.JPG
This little part is what makes the whole crane rotate!

The Top of the Tower

IMG_9654.JPG
IMG_9658.JPG
IMG_9660.JPG
IMG_9661.JPG
IMG_9662.JPG
IMG_9663.JPG
This will hold the jib and the counter weight on it's sides.

The Tower Tip

IMG_9664.JPG
IMG_9670.JPG
IMG_9671.JPG
IMG_9672.JPG
IMG_9602.JPG
IMG_9601.JPG
IMG_9603.JPG
IMG_9677.JPG

The Jib

IMG_9623.JPG
IMG_9624.JPG
IMG_9625.JPG
IMG_9602.JPG
IMG_9601.JPG
IMG_9632.JPG
IMG_9631.JPG
IMG_9629.JPG
IMG_9633.JPG
This will hold the hook and trolley.

The Counter Weight

IMG_9634.JPG
IMG_9602.JPG
IMG_9594.JPG
IMG_9639.JPG
IMG_9640.JPG
IMG_9644.JPG
IMG_9646.JPG
IMG_9647.JPG
IMG_9645.JPG
IMG_9649.JPG
IMG_9651.JPG
IMG_9652.JPG
IMG_9653.JPG
This small part will balance out the crane. 

The Support Rods

IMG_9694.JPG
IMG_9696.JPG
IMG_9697.JPG
IMG_9698.JPG
IMG_9631.JPG
IMG_9652.JPG
These slim pieces will help distribute the weight of the jib and counter weight so they don't break off.

The Winch

IMG_9683.JPG
IMG_9681.JPG
IMG_9682.JPG
IMG_9684.JPG
This will raise and lower the hook from the jib.

The Trolley Mechanism

IMG_9686.JPG
IMG_9688.JPG
This will move the trolley along the jib.

The Trolley

IMG_9707.JPG
IMG_9708.JPG
IMG_9709.JPG
IMG_9710.JPG
IMG_9711.JPG
IMG_9712.JPG
This will bring the hook along the jib.

The Hook

IMG_9713.JPG
IMG_9715.JPG
IMG_9717.JPG
IMG_9718.JPG
IMG_9719.JPG
IMG_9720.JPG
This will lift the load.

Inserting the Trolley Mechanism

IMG_9733.JPG
IMG_9722.JPG
IMG_9731.JPG
IMG_9749.JPG
This will connect the chain around through the jib.

Stringing Up the String

IMG_9737.JPG
IMG_9727.JPG
IMG_9730.JPG
IMG_9735.JPG
This will connect to the winch and the hook.

Assembling the Crane

IMG_9578.JPG
IMG_9760.JPG
IMG_9738.JPG
IMG_9742.JPG
IMG_9745.JPG
IMG_9762.JPG
IMG_9763.JPG
This will show you how to assemble the crane.