Knex Bass Drum Pedal Instructions

These are the instructions for my Knex Bass drum pedal that I created.

There have been some slight improvements on this that where not in the original

Rods

Longest - 19

- 3

- 21

- 3

- 82

Shortest - 239

One cut to six blue spacers long

Connectors

Black - 18

Yellow/White - 26+13

Green - 22

Red/Dark-gray - 26+10

Broken Red - 2

White - 18

Orange - 14

Light-gray/Purple - 4+1

3D Gray - 64

3D Blue - 16

Other Knex

Thin large wheel - 2

Thick large tyre - 1

Small wheel - 2

Small tyre - 2

Tan connector - 2

Blue connector - 3

Orange connector - 10

Black Y connector - 4

Black hinge connector - 2

Silver spacer - 15

Blue spacer - 13

Other

Hacksaw

Spring assembly for bass drum pedal:

• Nut
• Threaded rod with hole
• Tension spring

1. Make this part
2. And this part
3. Attach to the first part
4. Collect these
5. Make this
6. And this
7. Attach to first part
8. Make another, make sure its a mirror of first one
9. Aline the parts
10. Insert
11. Do the same on the other side

1. Make these
2. Attach the rods to the five parts
3. Attach rod
4. Put on the parts in this order
5. What you should have

1. Fill in the spaces
2. And on the other side
3. And here
4. Make these
5. Attach here
6. Aline part
7. Insert
8. Do the same on the other side

1. Make this
2. Different angle
3. Yet another angle
4. Aline the part here...
5. ... and here
6. Attach here...
7. ... and here
8. What you should have

1. Make this
2. Different angle
3. Yet another angle
4. Aline the part here...
5. ... and here
6. Attach here...
7. ... and here

1. Make these
2. Attach here
3. and on the other side

1. Make these...
2. And four more, you should have five of each
3. Attach 14 rods to a longer one
4. Attach a smaller one
5. Attach a longer one
6. Attach a smaller one
7. Attach a longer one
8. Attach a smaller one
9. Attach a longer one
10. Attach a smaller one
11. Attach a longer one
12. Attach a smaller one
13. Make this
14. Attach to main part
15. Get this
16. Insert
17. Attach
18. Get these
19. Insert and attach

1. Make these
2. Gather these
3. Make this
4. And another
5. Attach them together
6. Add the others
7. Aline together
8. Connect

1. Make this
2. Add these
3. And these
4. And these
5. And these
6. Make these
7. Attach to main part
8. And again

1. Add this
2. And this
3. And this
4. And this
5. Make this
6. Place here
7. Make sure its alined, doesn't matter at the moment but will later on
8. Make this
9. Attach here

1. Make this, use cut down rod
2. Add this
3. Attach to main part

1. Brake as seen, right pillar
2. Attach these
3. Insert through the axle, make sure to have spacer in the middle
4. Add spacer here
5. And here
6. And here
7. Connect as shown

1. Get this
2. Attach to spring
3. Move to hang inside the pillar, remove part
4. Place connector as shown
5. Thread on the nut
6. Re-attach the part

1. Add this
2. And these
3. Attach this
4. Add this
5. And this