Keyboard Bracelet With Interchangeable Keys

by atepinkrose in Craft > Jewelry

3105 Views, 25 Favorites, 0 Comments

Keyboard Bracelet With Interchangeable Keys

jeys.jpg
P1020564.jpg
123456.jpg
NO ELECTRIC COMPONENTS...just beading...you know...out of a keyboard...

Inspiration for the project:
My old laptop lost two keys while valiantly donating parts to save my wireless keyboard.  I kept the keys on my desk because I liked them and had decided to use the keys for jewelry but upon finishing the task of removing all the keys, wondered if I could keep the clickable mechanism.  

The main reason for my reasoning was to provide an interchangeable individual key platform for any key the same size and shape.


The wearer could change the word love for any word that did not have any repetitive letters.
L O V E
I A M Home
! < 3 U
I < 3 Home
C A T !
F R A K
E T C . 

Removing Key Board Keys and Board From Computer

P1020376.JPG
P1020377.JPG
P1020378.JPG
P1020379.JPG
P1020381.JPG
You will be removing the aluminum board on which the keys are laid on top of.

Using a thin flat head screw driver or knife wedge a knife into the bottom right edge of the board.  Insert the knife and pull back to separate the parts.

Unhook the aluminum board from computer frame.  Aluminum board has hooks.  See Images.

Final image gif shows the part being flapped up and down to break the final aluminum hooks to simplify the removal process.

Key Parts Removal and Separating and Organizing All the Parts.

P1020395.JPG
P1020399.JPG
P1020403.JPG
P1020404.JPG
P1020405.JPG
P1020406.JPG
Remove the All the key clasps till the plastic material with rubber key springs is exposed.  
Make sure you keep all your key clasps labeled in plastic bags depending on the size keys your keyboard has.

Making Lines on the Aluminum Board

P1020413.JPG
P1020410.JPG
P1020411.JPG
P1020412.JPG
With a straight edge and a pencil, draw a line by resting the straight edge on the top clasp and bottom clasp.  

See images.

Cut the Aluminum Board (CAUTION! SHARP EDGES)

P1020414.JPG
P1020415.JPG
P1020416.JPG
P1020417.JPG
P1020420.JPG
P1020426.JPG
Using kitchen shears, cut the board.  This will cause the aluminum to curl.

Flatten the strip with a straight edge. Cut two rows off the plastic piece too. You will probably not be able to see the line so eyeball-it  based on the pattern.  

And repeat.  This can be quite exhausting, therefore I would suggest only the first two rows and save the rest for another project.

Gluing the Plastic to the Aluminum

P1020433.JPG
P1020435.JPG
P1020436.JPG
P1020438.JPG
P1020428.JPG
I used craft bond spray adhesive but it is not the best for this task.  It works though.


Cut and Flatten

P1020442.JPG
P1020439.JPG
P1020440.JPG
P1020470.JPG
P1020443.JPG
Cut the strip into key sized parts, and flatten the curled edges with pliers.

Combine the Clasping Piece and the Letters

P1020460.JPG
P1020465.JPG
P1020464.JPG
P1020464.JPG
P1020468.JPG
The video shows how to add and remove a button and fix the clasping piece into an assembly.

See the video in the intro.  It shows how the complete assembly is put together and taken apart.

Dremel: Sanding the Edges Down

P1020482.JPG
P1020472.JPG
P1020477.JPG
If indoors you will need the following set up as seen in the primary image, in order to prevent aluminum dust from flying everywhere.

Make the Holes and Add the Clasps

P1020542.JPG
P1020513.JPG
P1020541.JPG
P1020498.JPG
P1020517.JPG
P1020532.JPG
P1020563.JPG
P1020577.JPG
Additional Steps not required inserted at the end of the instructable (mod podge and bead making). 

Line up the clasping mechanism part and determine the orientation.  Drill the holes and add the clasps.

CAUTION: Wear safety goggles when drilling

Drilling: <iframe width="420" height="315" src="http://www.youtube.com/embed/GxogbBPzFGs" frameborder="0" allowfullscreen></iframe>

Button Replacement: