Improve Password Security With Canned Beans
by rhettapplestone in Workshop > Metalworking
2255 Views, 14 Favorites, 0 Comments
Improve Password Security With Canned Beans
![image00017.jpeg](/proxy/?url=https://content.instructables.com/FC0/6T66/LH3FFF8X/FC06T66LH3FFF8X.jpg&filename=image00017.jpeg)
![image00004.jpeg](/proxy/?url=https://content.instructables.com/FEE/SZUU/LH3FFF8K/FEESZUULH3FFF8K.jpg&filename=image00004.jpeg)
Today we will be improving password security with the use of a set of metal punches and a new/old can of beans. If you store your passwords on a piece of paper, like many including myself in the past did, you are open to the possibility of paper smudges, water, or even fire destroying your passwords. With punched metal none of these are an issue.
Supplies
You will need
- Metal punches A-Z 0-9 + Special chars
- Can of beans
- Multi tool with pliers/scissors
- Object to hit the punch with
Rip Off the Label and Empty
![image00016.jpeg](/proxy/?url=https://content.instructables.com/FFZ/OG2A/LH3FFF8W/FFZOG2ALH3FFF8W.jpg&filename=image00016.jpeg)
![image00015.jpeg](/proxy/?url=https://content.instructables.com/F7G/2HQR/LH3FFF8V/F7G2HQRLH3FFF8V.jpg&filename=image00015.jpeg)
First you need to rip off the label, empty and clean the can, and cut the top and bottom off cleanly
Cut Down the Side
![image00014.jpeg](/proxy/?url=https://content.instructables.com/FKM/N0BM/LH3FFF8U/FKMN0BMLH3FFF8U.jpg&filename=image00014.jpeg)
![image00013.jpeg](/proxy/?url=https://content.instructables.com/F00/OZXS/LH3FFF8T/F00OZXSLH3FFF8T.jpg&filename=image00013.jpeg)
![image00012.jpeg](/proxy/?url=https://content.instructables.com/F07/Y3M8/LH3FFF8S/F07Y3M8LH3FFF8S.jpg&filename=image00012.jpeg)
Use pliers to make an initial entry to the can and cut all the way down
Flatten and Isolate Important Metal
![image00011.jpeg](/proxy/?url=https://content.instructables.com/FPJ/NXF6/LH3FFF8R/FPJNXF6LH3FFF8R.jpg&filename=image00011.jpeg)
![image00009.jpeg](/proxy/?url=https://content.instructables.com/FDS/SHAR/LH3FFF8P/FDSSHARLH3FFF8P.jpg&filename=image00009.jpeg)
![image00008.jpeg](/proxy/?url=https://content.instructables.com/FFU/OTX4/LH3FFF8O/FFUOTX4LH3FFF8O.jpg&filename=image00008.jpeg)
![image00005.jpeg](/proxy/?url=https://content.instructables.com/F3Y/LV5C/LH3FFF8L/F3YLV5CLH3FFF8L.jpg&filename=image00005.jpeg)
![image00006.jpeg](/proxy/?url=https://content.instructables.com/FAP/426P/LH3FFF8M/FAP426PLH3FFF8M.jpg&filename=image00006.jpeg)
![image00007.jpeg](/proxy/?url=https://content.instructables.com/FJL/4BDE/LH3FFF8N/FJL4BDELH3FFF8N.jpg&filename=image00007.jpeg)
You will want to flatten the entire can out, making sure to try not to crease it. Then cut off a long enough section and attempt to get only the flat part. Also make sure to cut off the lip of the can if you dont want it
Clean Up Edges and Make Your Password!
![image00002.jpeg](/proxy/?url=https://content.instructables.com/F4X/Y618/LH3FFF8G/F4XY618LH3FFF8G.jpg&filename=image00002.jpeg)
![image00003.jpeg](/proxy/?url=https://content.instructables.com/F5V/IQBJ/LH3FFF8J/F5VIQBJLH3FFF8J.jpg&filename=image00003.jpeg)
![image00001.jpeg](/proxy/?url=https://content.instructables.com/F9A/1MGC/LH3FFF8F/F9A1MGCLH3FFF8F.jpg&filename=image00001.jpeg)
I found punching on the dull side of the can increase readability. When punching make sure the surface you have will not retain the punch marks (security risk). To make a secure password aim for 14-16 characters with upper/lower/letter/symbols. Do not use re-use any password twice. You can also try punching directly on the top of the can which I found to work very well also. Aluminum beverage cans are flimsy, but could work. For uppercase/lowercase I put a little mark on those that I want to vary the case on (this saves you from having to buy a whole new case of punches)
It may be helpful to make a small holder as the metal is better than paper but can still be bent or broken.
I've included a fusion file of one that may work, feel free to change it as you see fit.
Hope you found this helpful!
Keychain PW Keeper
![Screenshot 2023-04-30 181821.png](/proxy/?url=https://content.instructables.com/FVW/WQKQ/LH3FFIKD/FVWWQKQLH3FFIKD.png&filename=Screenshot 2023-04-30 181821.png)
If you would like you are welcome to print a little keeper for keychain/other