Homemade 2'x4' Wood CNC Router

by Kyles Woodworking in Workshop > CNC

428547 Views, 889 Favorites, 0 Comments

Homemade 2'x4' Wood CNC Router

IMG_20110509_191959.jpg

Here I am going to show how I made my CNC (Computer Numerical Controlled) router. The table measures 24"x48" and the cutting envelope is about 19”x38.” I made this CNC when I was 17 years old and if you would like to see more on this CNC, visit my website at www.KylesWoodworking.com


NOTICE: THE PLANS AND DESIGN FOR THIS CNC WERE PRODUCED AND PURCHASED FROM WWW.BUILDYOURCNC.COM, ALL CREDIT FOR THE PLANS GO TO BUILD YOUR CNC. THE CNC STAND, COMPUTER STAND, AND ELECTRONICS BOX WERE DESIGNED BY ME.

CNC and Stand Assembly

Update CNC.JPG
IMG_20110212_195910.jpg
DSC00159.JPG
IMG_20110215_172541.jpg
IMG_20110215_172521.jpg
DSC00162.JPG
DSC00161.JPG
IMG_20110219_100537.jpg
IMG_20110219_210623.jpg
IMG_20110220_103220.jpg
IMG_20110217_175552.jpg
DSC00164.JPG
DSC00163.JPG
IMG_20110315_184823.jpg

The very first step of making a CNC is PLANS! I got plans and hardware kit from buildyourcnc.com which came with measurements for the CNC and all the nuts and bolts you need, besides the lead screws and various other parts. After I got the measurements of the CNC, I designed it on Google SketchUp as well as a stand for it and a computer to operate it. After I had a set design, I began building it. First, I made the CNC part of it and then I made the stand to fit. I used MDF for the CNC and 2x4s and 1/4" plywood for the stand. I also casters on the stand so I could move it around with ease.

Here you can see time lapse videos of me assembling the CNC and stand:

CNC:



Stand:


Lead Screws

DSC00165.JPG
DSC00166.JPG
DSC00167.JPG
DSC00168.JPG
DSC00169.JPG
DSC00170.JPG
IMG_20110220_214034.jpg
IMG_20110220_214044.jpg
IMG_20110220_214115.jpg
IMG_20110220_214127.jpg
The lead screws are what make the x,y, and z axis move by turning them with a motor. I went to the hardware store and picked up 1/2" threaded rods to use as the lead screws.

CNC Electronics

IMG_20110418_161852.jpg
IMG_20110428_204854.jpg
IMG_20110428_204913.jpg
IMG_20110428_204927.jpg
IMG_20110428_204936.jpg
IMG_20110430_191025.jpg
IMG_20110430_191043.jpg
IMG_20110430_191054.jpg
IMG_20110430_191107.jpg
IMG_20110430_191120.jpg
IMG_20110430_191129.jpg
IMG_20110430_191003.jpg
IMG_20110430_191142.jpg
IMG_20110509_190650.jpg
IMG_20110509_190659.jpg

The next and most expensive step is the electronics. I got the electronics kit from buildyourcnc.com and I made a box out of wood and plexiglass to house the electronics. The electronics kit included:

(3) 425 oz-in stepping motors

(3) Drivers (3.0Amp 24-40 Volts, 1-1/64 micro-stepping)

(1) 36v 8.8a Power Supply

(1) Breakout board

I wired all the electronics up and added a few more features such as, an e-stop switch, limit switches, and power switches for the router, shop vac, electronics, and the stepping motors.


Here you can view a video of the electronics:


Finished and Test Cut

IMG_20110509_192303.jpg
IMG_20110430_191043.jpg
IMG_20110509_191959.jpg
IMG_20110509_192012.jpg
IMG_20110509_192110.jpg
IMG_20110509_192313.jpg

The final step is to make a test cut. I made a test cut of my logo into pine. The software I use is Google SketchUp to design it and then a plugin to convert it into g-code and Mach3 to control it. The total cost of this CNC was about $700.


Here you can view a video of my first test cut: