How to Make Quadcopter With Kk2.1.5 Flight Controller

by DevBroz in Circuits > Remote Control

3728 Views, 3 Favorites, 0 Comments

How to Make Quadcopter With Kk2.1.5 Flight Controller

Q450-quadcopter-kopen.jpg

Hi Guys Today We are Making Quadcopter With Kk2.1.5 Flight Controller

Warnings While Flying or Making Quadcopters

1)Consider your safety first.

2)Start trying to fly in an open field.

3)Practice landing.

4)Maintain a lower altitude.

5)While configuring quardcopter please remove all the propeller.

Materials Used

DSCN6890.JPG
DSC_0088.JPG
DSC_0089.JPG
DSCN6905.JPG
DSCN6929.JPG
DSCN6896.JPG
diatoneq450v3_b_1.jpg
ROB2586-500x500.jpg
DSC_0096.JPG

Hardware Items:
1) Quadcopter Frame.

2) Flight Controller (KK 2.15 Flight Controller)

3) Brushless Motor (1000KV) (4 pieces)

4) Electronic Speed Control [ESC] (30 Amps) -4 pieces

5) Propellers 1045/1045R -2 sets

6) Lithium-Polymer 2200 mAH Battery-1

7) FS-CT6B 6-Channel (Transmitter+Receiver)-1

8) 1.5 Volt Batteries for Transmitter- [According to the Transmitter]

Product Links:

1)Motor - https://amzn.to/2XGrahE

2)ESC - https://amzn.to/2XGrahE

3) Flight Controller- https://amzn.to/2XGrahE

4) Battery - https://amzn.to/2XGrahE

5) Transmitter+Receiver - https://amzn.to/2XGrahE

6) Battery Charger - https://amzn.to/2XGrahE

7) Propeller - https://amzn.to/2XGrahE

Tools ​Needed :

1) Solder iron.

2) Alan keys tool.

3) Shrink tubes.

4) Glue gun.

5) Zip ties (To hold the ESC's on the frame and for tying some wires)

Connect Motor With ESC

DSCN6876.JPG

Connect the 4 Motors and ESC's each other by direct soldering or using Connectors.

Connect ESC to Power Distribution Board

DSCN6880.JPG
DSCN6874.JPG

Then connect the ESC's using connector or by directly soldering.to the inbuilt power distribution board.

Solder the Battery Wire

DSCN6886.JPG

Solder the Battery wire to the inbuilt power distribution board and if needed you can also add a switch.

KK 2.15 Board Connection

DSCN6913.JPG
DSCN6911.JPG
DSCN6894.JPG

After all the soldering work is done,connect the Receiver and ESC servo wires to KK 2.15 Board.

Transmitter Programming

image1.jpg

1)Connect the controller to your desktop or laptop and open configure
application [T6Config Software if you are using FS-CT6B 6-Channel] and test the controls to see the Throttle,Elevator-Pitch, Rudder-Yaw and Aileron-Altitude are not inverted.

2)If you don't know how to program transmitter don't worry,download our programmed file below and open it on T6Config Software

Programming and Arming the KK 2.15 Board

DSCN6919.JPG
DSCN6921.JPG
DSCN6923.JPG
images.jpg

1) If your code is all correct and your connections are all good,connect the Battery and Switch on the Drone,You should see the LCD screen on the KK2.1.5 board lit up,from where you can easily calibrate
2) Set End points to 100% and subtrim each channel according to your needs and quadcopter's stability.

3)Now arm the KK 2.15 Board (You'd see ARMED come up on the LCD screen) and gradually increase the throttle. If everything is perfecty connected, flashed and calibrated the motors will start rotating.

For More about Programming Watch This:

For More About Making Quadcopter you can watch our YouTube Video Below:

Now You Are Done!!

DSC_0091.JPG
DSCN6889.JPG
DSCN6916.JPG

Now fix propeller START FLYING :)
Thank You for reading our tutorial.Please do drop a vote for us if you like the build.

Thank You

Dev Broz