How to Make Electric Remote Train From a Cardboard?

by svenix in Living > Toys & Games

3600 Views, 6 Favorites, 0 Comments

How to Make Electric Remote Train From a Cardboard?

Как сделать поезд с моторчиком и пульт из картона и крышек?

In this article, we will show how to make a railroad from cardboard and lids, as well as a remote control with which we will manage the train.

We will need:

- Motor with gear

- old USB cable with socket

- a piece of elastic tin

- caps from plastic bottles

- a piece of plastic (you can take the old CD-ROM)

- Soldering iron, wire cutters and other tools.

1 We Make the Train.

1550440213_youtu_be-bkfh70vdqzm.jpg
1550440293_youtu_be-bkfh70vdqzmiaichi.jpg
1550440272_aiaap.jpg
1550440286_ddshschshjushschschzje.jpg

First of all we cut out the base of the train as in the picture.

Then we mark the place for the engine and make a seat for it.

We also make holes for the axis of the gearbox where we install the wheels.

​Making Wheels

1550440246_poppropr.jpg
1550440315_propropvvvv.jpg
1550440296_vapvaaptptaptvava.jpg

We prepare the caps, cut off the excess part and smooth the edge; we make small covers with the same size as the large ones.

Cut a circle from a CD or similar plastic a few millimeters more than the prepared caps.

​Making Еlectro Wheels

1550440270_ljugjujuz.jpg
1550440273_praarap.jpg

We wrap copper wire on large wheels, after sanding it from varnish, these wheels will be electrically conductive.

Fix the wire with super glue on the cap.

Sliding Contacts

1550440287_ch-chsmyvp-uk-uk.jpg
1550440294_vpvapvapvapvapvapva.jpg
1550440240_vervprrr.jpg
1550440255_aprapvvvarrkrke.jpg
1550440241_vapvapavpavpavpvvupkra.jpg
1550440274_kerkr.jpg

We select a pair of capacitors of approximately the same diameter as the axis of the gearbox shaft and disassemble them. We need only the external aluminum part of the capacitors.

We put the "P" shaped wire on the axis of the gearbox and fasten it by installing a 3 cm wire.

We dress the sleeve from the condenser onto the axle and fill it with super glue so that our construction holds well.

Sliding Brushes

1550440203_youtu_be-bkfh70vdqzm-14.jpg
1550440114_youtu_be-bkfh70vdqzm-1.jpg
1550440120_youtu_be-bkfh70vdqzm-2.jpg
1550440157_youtu_be-bkfh70vdqzm-3.jpg
1550440189_youtu_be-bkfh70vdqzm-4.jpg

Install the prepared gear on the train frame and glue with thermal glue.

We make two sliding contacts from the wire, which will slide along the aluminum sleeves on the gearbox axis.

At the ends of the wire we make hooks and we hook on the gum, so that there is good contact.

To the other end we solder the wires and connect to the motor.

We Collect Wheels

1550440141_youtu_be-bkfh70vdqzm-5.jpg
1550440130_youtu_be-bkfh70vdqzm-6.jpg
1550440133_youtu_be-bkfh70vdqzm-7.jpg

We solder the wires from the electric wheels onto the axle, the plastic circle with glue also onto the axle, and the lid on it, the rest of the wheels are done in a similar way only without electrical contacts.

​We Collect the Train Body

1550440123_youtu_be-bkfh70vdqzm-8.jpg
1550440192_youtu_be-bkfh70vdqzm-9.jpg
1550440208_youtu_be-bkfh70vdqzm-10.jpg

We Assemble the Body and Wheels of Cars

1550440151_youtu_be-bkfh70vdqzm-12.jpg
1550440115_youtu_be-bkfh70vdqzm-11.jpg
1550440163_youtu_be-bkfh70vdqzm-13.jpg

The Manufacture of the Railway.

1550440219_youtu_be-bkfh70vdqzm-16.jpg
1550440156_youtu_be-bkfh70vdqzm-15.jpg
1550440185_youtu_be-bkfh70vdqzm-17.jpg
1550440176_youtu_be-bkfh70vdqzm-18.jpg
1550440189_youtu_be-bkfh70vdqzm-19.jpg

We cut the cardboard into long strips; these will be rails and short for sleepers. Also we cut out the connecting places as in the picture.

We tear off a strip of usual kitchen foil and we wind it with rails.

Strengthening Compounds

1550440132_youtu_be-bkfh70vdqzm-20.jpg
1550440159_youtu_be-bkfh70vdqzm-21.jpg
1550440169_youtu_be-bkfh70vdqzm-22.jpg
1550440156_youtu_be-bkfh70vdqzm-23.jpg

Glue the rails wrapped with foil to the cross ties and connect. When gluing in the joints, we make a gap of about 3 mm so that when collecting the road there is a better contact.

It should look like in the photo. We try to make a road with a large diameter, so the train keeps better on the tracks.

Glue the auxiliary segments on the sides of the connecting sections so that the rails in these places do not go right and left.

Electrical Contacts on Rails

1550440198_youtu_be-bkfh70vdqzm-24.jpg
1550440222_youtu_be-bkfh70vdqzm-25.jpg
1550440150_youtu_be-bkfh70vdqzm-26.jpg

One section is glued to a solid cardboard, there will be a station. In the corner of the station near the rail, we conduct two wires and fasten them to the rails, we wrap the top with foil to hide the wires and better contact.

Remote Controller

1550440215_youtu_be-bkfh70vdqzm-29.jpg
1550440142_youtu_be-bkfh70vdqzm-27.jpg
1550440203_youtu_be-bkfh70vdqzm-30.jpg
1550440245_youtu_be-bkfh70vdqzm-31.jpg
1550440218_youtu_be-bkfh70vdqzm-32.jpg

In the lid make two holes for toothpicks. We put one toothpick in the center, and the second with the edge on the lid. We set the side toothpick so that it protrudes a little to 5 mm, and the rest of it is bitten off.

On the inside of the lid, glue the paper plugs and leave the toothpick sticking out on both sides.

We make rounded contacts with a metal contact lug. And glue with hot glue to the lid.

Contacts

1550440205_youtu_be-bkfh70vdqzm-33.jpg
1550440205_youtu_be-bkfh70vdqzm-34.jpg
1550440169_youtu_be-bkfh70vdqzm-35.jpg
1550440252_youtu_be-bkfh70vdqzm-36.jpg

We also make a “P” - shaped contact and fasten the wire in the middle.

Putting them together so that one side is parallel, and the second is crosswise. The intersecting contact is insulated by shrinking.

Glue the contacts and the cover to the base of the console so that the rotating contacts of the cover are inside the fixed.

Fix the swivel cover with a cardboard washer.

Battery Compartment

1550440192_youtu_be-bkfh70vdqzm-37.jpg
1550440189_youtu_be-bkfh70vdqzm-38.jpg
1550440256_youtu_be-bkfh70vdqzm-39.jpg
1550440208_youtu_be-bkfh70vdqzm-40.jpg
1550440222_youtu_be-bkfh70vdqzm-41.jpg

Cut and glue the compartment for three AA batteries

We also cut out contacts for batteries from elastic tin and put them in place.

We solder the wires to the compartment with batteries and glue them to their place in the console.

Management Stick

1550440234_youtu_be-bkfh70vdqzm-422.jpg
1550440265_youtu_be-bkfh70vdqzm-42.jpg
1550440249_youtu_be-bkfh70vdqzm-43.jpg
1550440255_youtu_be-bkfh70vdqzm-44.jpg

Fix the wire on the remote and solder to the cover with the contacts.

With a rubber band, we make a loop and glue it on the side ledge of the lid, and fix the other two ends with thermo-glue on the console case. This is necessary so that when the gas is released, the train automatically stops.

Management Stick

1550440201_youtu_be-bkfh70vdqzm-45.jpg
1550440175_youtu_be-bkfh70vdqzm-46.jpg
1550440178_youtu_be-bkfh70vdqzm-47.jpg

From the ice cream sticks we make a lever to move back and forth and collect the remaining parts of the body from the console.

Place for Batteries

1550440195_youtu_be-bkfh70vdqzm-49.jpg
1550440247_youtu_be-bkfh70vdqzm-50.jpg

Cover the battery cover with one side glued to the body, and with the other fasten velcro.

For convenience, we attach the thread to the battery compartment so that by pulling on it you can easily reach the batteries.

Improved Train Contact

1550440264_youtu_be-bkfh70vdqzm-51.jpg
1550440224_youtu_be-bkfh70vdqzm-52.jpg
1550440208_youtu_be-bkfh70vdqzm-53.jpg

When operating the train, there may be a loss of contact between the wheels and the rails and the toy will stop.

So that the contact was reliable, under the train you need to make two contacts that will remove electricity from the rail.

Makes Heavy

1550440226_youtu_be-bkfh70vdqzm-54.jpg
1550440247_youtu_be-bkfh70vdqzm-55.jpg

Also, so that the train does not slip on the rails, it is necessary to put gum on the wheels, and attach a load to the train itself.

Wagon Connection

1550440227_youtu_be-bkfh70vdqzm-56.jpg
1550440198_youtu_be-bkfh70vdqzm-57.jpg

With the wire we make hooks between the cars and glue them into place.

Теst

1550440269_youtu_be-bkfh70vdqzm-58.jpg
1550440286_youtu_be-bkfh70vdqzm-60.jpg
1550440248_youtu_be-bkfh70vdqzm-59.jpg

We collect the railway, at the junction we join and put on rubber bands.

Connect the remote to the road, everything is ready.

We press on the gas and the engine begins to move along the rails.

Conclusion:

You will have a funny paper railway with your own hands. All the kids will be happy to do hand-made articles. The manufacturing process requires a lot of perseverance and develops fine motor skills. And it is necessary to play a hand-made article neatly, nevertheless, it is paper and fragile. Thanks for attention.

Source