Hardin-F-180 Furnace Thermocouple Replacement
by jhudson20 in Workshop > Metalworking
2731 Views, 5 Favorites, 0 Comments
Hardin-F-180 Furnace Thermocouple Replacement
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/F4G/OO97/IBQCGJIL/F4GOO97IBQCGJIL.jpg&filename=15, 7:25 PM.jpg)
How I figured out how to replace the thermocouple on a Hardin 180 furnace.
Removal of Mesh Gaurd
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/FFS/DGFZ/IBQCGJIJ/FFSDGFZIBQCGJIJ.jpg&filename=15, 7:25 PM.jpg)
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/FLR/P0MI/IBQCGJJL/FLRP0MIIBQCGJJL.jpg&filename=15, 7:25 PM.jpg)
Remove the 6 screws with washers holding mesh Heat guard in place. Ceramic cones may or may not stay in place.
Lid Assembly
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/FFI/LOMW/IBQCGJJM/FFILOMWIBQCGJJM.jpg&filename=15, 7:25 PM.jpg)
Remove 4 screws on back holding lid assembly to furnace body. Set aside.
Access Plate
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/F89/ZRZK/IBQCGJKO/F89ZRZKIBQCGJKO.jpg&filename=15, 7:25 PM.jpg)
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/FVL/BYQL/IBQCGJKP/FVLBYQLIBQCGJKP.jpg&filename=15, 7:25 PM.jpg)
Turn oven assembly upside down and remove the 4 screws holding it in place
Removal of Thermal Couple
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/FTG/R3PT/IBQCGJM5/FTGR3PTIBQCGJM5.jpg&filename=15, 7:25 PM.jpg)
Remove the 2 screws holding coupler to body.
Temperature Control Panel
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/FRS/PB90/IBQCGJM6/FRSPB90IBQCGJM6.jpg&filename=15, 7:25 PM.jpg)
Loosen screws from back of control panel where thermocouple is connected to. ( keep in mind the proper placement colors of the wires)
Swapping Out Coupler
Pull old out and place in new.
Reattach Thermocouple
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/FWO/6YVG/IBQCGJM9/FWO6YVGIBQCGJM9.jpg&filename=15, 7:25 PM.jpg)
![15, 7:25 PM.jpg](/proxy/?url=https://content.instructables.com/F65/SUG6/IBQCGJMA/F65SUG6IBQCGJMA.jpg&filename=15, 7:25 PM.jpg)
Reattach thermocouple to body and reattach wires to back of control panel. Zip tie loose wire to the rest of the wires.
Reattach the Rest
![15, 7:26 PM.jpg](/proxy/?url=https://content.instructables.com/FZL/NNFK/IBQCGJMC/FZLNNFKIBQCGJMC.jpg&filename=15, 7:26 PM.jpg)
![15, 7:26 PM.jpg](/proxy/?url=https://content.instructables.com/F2T/WKCJ/IBQCGJMD/F2TWKCJIBQCGJMD.jpg&filename=15, 7:26 PM.jpg)
![15, 7:26 PM.jpg](/proxy/?url=https://content.instructables.com/FZW/P9L0/IBQCGJME/FZWP9L0IBQCGJME.jpg&filename=15, 7:26 PM.jpg)
Reattach access panel, lid assembly, and mesh guard. In that order.
Test
Turn on. Run in 3 wave.
1st- 400 C;
COOL ;
2nd-800 C;
COOL;
3rd-1150 C
Never leave unattended.
1st- 400 C;
COOL ;
2nd-800 C;
COOL;
3rd-1150 C
Never leave unattended.