GoPro 90-degree Adapter
![DSCN2705[1].JPG](/proxy/?url=https://content.instructables.com/FVL/1324/IIT975FP/FVL1324IIT975FP.jpg&filename=DSCN2705[1].JPG)
![DSCN2706[1].JPG](/proxy/?url=https://content.instructables.com/F3I/5TM7/IIT975P0/F3I5TM7IIT975P0.jpg&filename=DSCN2706[1].JPG)
this is a cheap way to make an adapter like the one that comes with the handlebar and rollcage mounts
mine was missing it as it was used so i made this
Materials
![DSCN2682[1].JPG](/proxy/?url=https://content.instructables.com/FTH/1AK1/IIT9753R/FTH1AK1IIT9753R.jpg&filename=DSCN2682[1].JPG)
![DSCN2685[1].JPG](/proxy/?url=https://content.instructables.com/F6Z/MRL8/IIT9755Z/F6ZMRL8IIT9755Z.jpg&filename=DSCN2685[1].JPG)
![DSCN2686[1].JPG](/proxy/?url=https://content.instructables.com/FGM/6D0J/IIT97560/FGM6D0JIIT97560.jpg&filename=DSCN2686[1].JPG)
![DSCN2697[1].JPG](/proxy/?url=https://content.instructables.com/F8I/B525/IIT975D4/F8IB525IIT975D4.jpg&filename=DSCN2697[1].JPG)
![DSCN2703[1].JPG](/proxy/?url=https://content.instructables.com/F9O/PZ42/IIT975UA/F9OPZ42IIT975UA.jpg&filename=DSCN2703[1].JPG)
The point of this adapter is to turn your GoPro 90-degrees for a side view
You will need:
- Epoxy Glue
- 2 DISPOSABLE GoPro QuickClips ( I used 1 broken one and 1 third party one. make sure u have one more to use)
- Paper Plate
- Toothpicks
- a coarse & small fine file
- Clamp
Gluing
![DSCN2687[1].JPG](/proxy/?url=https://content.instructables.com/FHI/G7K3/IIT97589/FHIG7K3IIT97589.jpg&filename=DSCN2687[1].JPG)
![DSCN2688[1].JPG](/proxy/?url=https://content.instructables.com/FL5/U4QS/IIT9758B/FL5U4QSIIT9758B.jpg&filename=DSCN2688[1].JPG)
![DSCN2689[1].JPG](/proxy/?url=https://content.instructables.com/F49/O7YQ/IIT975AK/F49O7YQIIT975AK.jpg&filename=DSCN2689[1].JPG)
![DSCN2690[1].JPG](/proxy/?url=https://content.instructables.com/F74/5XT0/IIT975AU/F745XT0IIT975AU.jpg&filename=DSCN2690[1].JPG)
MAKE SURE TO DO THIS PART OUTSIDE!!!! "Epoxy Resin can cause eye and skin burns and respitory tract irritation"
I got some on my hand and was fine, but its best just to avoid touching it while wet.
- ok, first squeeze the glue out on to the plate and use the toothpick to stir it
- then dip each clip into the mixture. use the toothpick to spread it around
- then put the 2 clips together as seen in the picture, and clamp it for at least 30 min.
Filing
![DSCN2695[1].JPG](/proxy/?url=https://content.instructables.com/FIW/CN6G/IIT975D3/FIWCN6GIIT975D3.jpg&filename=DSCN2695[1].JPG)
![DSCN2697[1].JPG](/proxy/?url=https://content.instructables.com/FL6/LA64/IIT97DXD/FL6LA64IIT97DXD.jpg&filename=DSCN2697[1].JPG)
![DSCN2698[1].JPG](/proxy/?url=https://content.instructables.com/F4L/42OO/IIT97DXF/F4L42OOIIT97DXF.jpg&filename=DSCN2698[1].JPG)
![DSCN2699[1].JPG](/proxy/?url=https://content.instructables.com/FS6/KRTS/IIT97E0E/FS6KRTSIIT97E0E.jpg&filename=DSCN2699[1].JPG)
![DSCN2701[1].JPG](/proxy/?url=https://content.instructables.com/FP0/WT19/IIT97E3I/FP0WT19IIT97E3I.jpg&filename=DSCN2701[1].JPG)
![DSCN2702[1].JPG](/proxy/?url=https://content.instructables.com/FIH/OFN6/IIT97E0G/FIHOFN6IIT97E0G.jpg&filename=DSCN2702[1].JPG)
Now it is time to shape the bottom part
- remove the metal nut off the end of 1 of the clips
- then use a coarse file to saw off one of the 3 prongs(as seen)
- use the fine file to smooth things out
- take the small file and cut down on the edges in between and around the prongs
- you may have to drill larger holes to attach it to your mounts
- if so, use a 1/4 or 7/32 drill bit and file the edges again
DONE!!!
![DSCN2705[1].JPG](/proxy/?url=https://content.instructables.com/FN5/NTHI/IIT97IG1/FN5NTHIIIT97IG1.jpg&filename=DSCN2705[1].JPG)
![DSCN2706[1].JPG](/proxy/?url=https://content.instructables.com/FCW/8AYN/IIT97IJ2/FCW8AYNIIT97IJ2.jpg&filename=DSCN2706[1].JPG)
this mount was designed for use on the handlebar or rollcage mount. it normally comes with the mount, but mine was used and was missing it
thanx