Giant Pipe Cutter

by mikeandmertle in Workshop > Tools

593 Views, 10 Favorites, 0 Comments

Giant Pipe Cutter

Pipe Clamp.png
Pipe Cutter

I have small pipe cutters, large pipe cutters, but I don't have giant pipe cutters. This instructable is my attempt to make some giant pipe cutters.

While these seem to work, I aren't 100% happy with the performance. I think the issue is that the cutting wheel isn't sharp enough, that's why I recommend just buying a cutting wheel.

Anyway, I decided to post these instructions hoping someone else can improve on my original design.

Supplies

  • Plywood
  • Bolts
  • Washers
  • Ball Bearing Races
  • Epoxy Glue
  • Clamp
  • Drill
  • Jigsaw
  • Screws
  • Ginder
  • Sandpaper

20240518_172741.jpg
20240519_113842.jpg

Print out the attached templates and glue it onto a piece of plywood. Once the glue is dry use a jigsaw to cut everything out.

Downloads

Drilling

20240519_114536.jpg
20240519_114826.jpg

Drill the marked holes on the template and then bolt the matching parts together.

Smooth the Parts

20240519_115020.jpg
20240519_115023.jpg
20240519_120810.jpg
20240519_120816.jpg
20240519_121741.jpg

Now that the common parts are bolted together I used a wood rasp to make sure the parts match in size. I then sanded everything smooth and undone the bolts.

Make the Rollers

20240519_124806.jpg
20240519_125241.jpg
20240519_125253.jpg
20240519_141534.jpg
20240519_141805.jpg
20240519_162100.jpg

I found a few old bearings to use as rollers, the ones I had were probably a little small but managed to do the job. The problem was that the internal holes were too big, so I found a piece of pipe that fit inside snuggly and cut off a small length for each bearing. I then filled the inside of the pipe with epoxy and once it had set drilled a 6mm hole in the centre.

The Blade

20240519_144120.jpg
20240519_150515.jpg
20240519_150738.jpg
20240519_151033.jpg
20240519_151112.jpg
20240519_162246.jpg
20240519_162754.jpg
20240519_162808.jpg
20240519_164616.jpg
20240519_165133.jpg

I used an offcut of an old mill saw blade, marked out a circle with some dividers and cut it out with an angle grinder. After drilling a hole through the centre I used a bolt to hold the circle in the drill and spun it against the grinder to make sure it was perfectly round. Finally, I ground an edge on each side of the circle to make a cutting wheel.

To be honest I weren't happy with the result and recommend just buying a pre-made pipe cutter wheel.

Assemble

20240519_170521.jpg
20240519_170526.jpg
20240519_171202.jpg
20240519_171431.jpg

I bolted the parts together using washers on either side of the rollers. For the cutting wheel, I packed out each side with a few washers.

Clamp Mounts

20240523_172502.jpg
20240523_172505.jpg
20240523_172510.jpg

When I got to this point I wasn't 100% sure how to make a clamping system, but decided to just make some mounts that a standard clamp could lock onto.

I ended up extending the plywood so my clamp would reach it. These extensions were quickly screwed in place.

Attach the Clamp

20240523_172856.jpg
20240523_172903.jpg
20240523_173205.jpg
20240523_173519.jpg
20240523_175259.jpg

The easiest way to attach the clamp was to drill a slot on one end with a forstner bit and a hole clamped between a couple of large washers on the other end.

The clamp will then lock into the slots and apply pressure to the cutting wheel.

Cut the Pipe

20240523_175248.jpg
20240523_175245.jpg
20240523_173522.jpg
20240523_173528.jpg
20240523_174005.jpg
20240523_174011.jpg
20240523_174958.jpg

To use the pipe cutter just fold the cutter around the pipe and then use the clamp to apply pressure. As you rotate the cutter around the pipe you just need to periodically tighten the clamp.

The advantage of using a pipe cutter is that you get a perfectly straight cut.