Dart Flights

by TRXbloke in Living > Toys & Games

348 Views, 0 Favorites, 0 Comments

Dart Flights

P1030893.JPG
P1030891.JPG

Homemade Dart Flights, using crisp packets (or other thin film).

Supplies

P1030861.JPG

You will need: Thin card, scissors, ruler, compasses, a crisp packet and an indelible pen (not pictured).

Make Card Template

P1030860.JPG
P1030862.JPG
P1030864.JPG

1/ Set compasses to 42mm and draw a circle onto the card.

2/ Roughly cut out a square including the circle.

3/ Carefully cut out your 84mm diameter card circle template.

Cut Crisp Packet Circle

P1030865.JPG
P1030866.JPG

1/ Degrease crisp packet.

2/ Place card circle where you wish to cut your circle.

3/ Draw around the card onto the crisp packet.

4/ Carefully cut out your crisp packet circle.

Primary Fold

P1030867.JPG
P1030868.JPG
P1030869.JPG

1/ Fold crisp packet circle in half.

2/ Create a sharp crease.

3/ Open out and flatten.

Second Fold

P1030870.JPG
P1030871.JPG

1/ Carefully align 1st crease to match up and fold circle in half so fold is 90 degree to 1st fold.

2/ Create a sharp 2nd crease.

Inner Fold

P1030872.JPG
P1030873.JPG
P1030874.JPG
P1030875.JPG
P1030876.JPG
P1030877.JPG
P1030879.JPG

1/ Fold both creases and pinch with 4 fingers to create shape shown in pic. 1 and 2.

2/ Align edge and pinch between fingers (pic 3).

3/ Find loop inside (pic 4) and pinch (pic 5).

4/ Use the pinched edge to create the inside fold, and squeeze inside edges (pic 6)

5/ Lay flat on a hard surface and run flat of finger nail along middle to create a sharp crease.

2nd Inner Fold

P1030880.JPG
P1030882.JPG
P1030883.JPG
P1030884.JPG

1/ Open out folded flight and align the opposing edges.

2/ Pinch out and crease along the centre ridge as with the previous fold.

That concludes the folding

Marking the Shape

P1030885.JPG
P1030886.JPG
P1030887.JPG
P1030888.JPG

1/ Select a flight whose shape you like. You need to choose a shape of flight with a right angle bit at the pointy end.

2/ Align carefully and draw around the flight using an indelible pen.

Finishing Cut

P1030889.JPG
P1030890.JPG
P1030893.JPG

1/ Using very sharp scissors, carefully cut the shape. You may need to trim the rear wings as the film will slide a little during cutting. It may be better to cut just the front wing first. then follow that for the rear wings of the flight.

2/ Flight is ready for use.

3/ You can (if you wish) glue the wing sides together, using a glue stick. Be very sparing with the glue (add some moisture and smear with your finger) or the flight will become lumpy and distorted.

The Benefit

P1030848.JPG
P1030854.JPG

These flights are significantly lighter and more aerodynamic than any modern flight available to buy. Your darts will fly faster, truer, and be better balanced. You will have less bounce outs and deflections. The flights are so thin that an incoming dart is more likely to go straight through the flight than deflect off it, and as they cost nothing, "Robin Hood" shots cost nothing and actually become a thing of the past.

I know these flights improved my game by at least a 10 point average. Hope they help yours.