DIY Simple Wireless Charging Stand
by Raghavendra g in Circuits > Wireless
2224 Views, 6 Favorites, 0 Comments
DIY Simple Wireless Charging Stand
![20180427_224224.jpg](/proxy/?url=https://content.instructables.com/FTK/D2D2/JGGTGQ3E/FTKD2D2JGGTGQ3E.jpg&filename=20180427_224224.jpg)
![20180427_225514.jpg](/proxy/?url=https://content.instructables.com/FGK/427V/JGGTGQF5/FGK427VJGGTGQF5.jpg&filename=20180427_225514.jpg)
![20180427_230624.jpg](/proxy/?url=https://content.instructables.com/FJN/441C/JGGTGP70/FJN441CJGGTGP70.jpg&filename=20180427_230624.jpg)
We all have seen wireless chargers which use resonance coupling to charge devices. But here is a phone charger which can be used to charge most of mobile phones. It works due to contact between two terminals........... In this charger a USB b type pin must be connected to the phone and has to be placed on the stand ,due to contact between terminals phone charges! Its not a big deal...
making this instructable is very easy and requirements are easily available.
REQUIREMENTS
- SUN BOARD (PVC FOAM SHEET)
- MICRO USB PIN (male and female)
- some thin uninsulated wires ,soldering iron
- expory putty compound(M-seal)
- glue, paint,and some tools
DRAW YOUR DESIGN
![Untitled.png](/proxy/?url=https://content.instructables.com/FTE/KF3T/JGGTIBUY/FTEKF3TJGGTIBUY.png&filename=Untitled.png)
You can make your on design....how ever you want
while sketching make sure that you make it suitable for all phones,by expanding side grips.
CUT THEM ALL
![IMG-20180428-WA0008-2.jpg](/proxy/?url=https://content.instructables.com/FTO/ERU3/JGGTIBZJ/FTOERU3JGGTIBZJ.jpg&filename=IMG-20180428-WA0008-2.jpg)
![IMG-20180428-WA0002-1.jpg](/proxy/?url=https://content.instructables.com/FMS/J3LK/JGGTIC01/FMSJ3LKJGGTIC01.jpg&filename=IMG-20180428-WA0002-1.jpg)
Cut all the pieces using a cutter.
be careful while cutting.don't cut them slantly,it would look ugly
GLUE ALL THE PIECES
![20180427_160816.jpg](/proxy/?url=https://content.instructables.com/FU8/EE7J/JGGTIR1B/FU8EE7JJGGTIR1B.jpg&filename=20180427_160816.jpg)
![20180427_160930.jpg](/proxy/?url=https://content.instructables.com/FLO/XBG9/JGGTGL6I/FLOXBG9JGGTGL6I.jpg&filename=20180427_160930.jpg)
Glue the parts
- Parts of stand
- Two grips
MAKING THE BASE TERMINALS
![20180427_175447.jpg](/proxy/?url=https://content.instructables.com/FMF/FWZ7/JGGTGM0P/FMFFWZ7JGGTGM0P.jpg&filename=20180427_175447.jpg)
![20180427_183705.jpg](/proxy/?url=https://content.instructables.com/F10/9ZTQ/JGGTGML9/F109ZTQJGGTGML9.jpg&filename=20180427_183705.jpg)
![20180427_181119.jpg](/proxy/?url=https://content.instructables.com/FW1/55BW/JGGTGM76/FW155BWJGGTGM76.jpg&filename=20180427_181119.jpg)
Now lets make contact terminals.
I have used soldering lead to do this because is can be bent easily.
- glue it to a small piece of sun board as in picture.make two pieces
- And now attach it to previosly made base holder.
- make a hole at lower base of stand for usb pin or for charger's input
- And finally glue the holder to stand
MAKING THE CONNECTER PIN TO MOBILE
![20180427_163200.jpg](/proxy/?url=https://content.instructables.com/F1C/1WBK/JGGTGLDP/F1C1WBKJGGTGLDP.jpg&filename=20180427_163200.jpg)
![20180427_163336.jpg](/proxy/?url=https://content.instructables.com/F9J/4C7C/JGGTGLDQ/F9J4C7CJGGTGLDQ.jpg&filename=20180427_163336.jpg)
![20180427_164212.jpg](/proxy/?url=https://content.instructables.com/FFB/7LTL/JGGTGLKY/FFB7LTLJGGTGLKY.jpg&filename=20180427_164212.jpg)
From a old data cable remove the micro usb pin
- solder the two terminals with a uninsulated wires to make contact terminal
COVERING THE PIN
![20180427_165041-1.jpg](/proxy/?url=https://content.instructables.com/FVN/A7B6/JGGTGLS9/FVNA7B6JGGTGLS9.jpg&filename=20180427_165041-1.jpg)
![20180427_165148.jpg](/proxy/?url=https://content.instructables.com/FZJ/9BC3/JGGTGLVW/FZJ9BC3JGGTGLVW.jpg&filename=20180427_165148.jpg)
![20180427_192348.jpg](/proxy/?url=https://content.instructables.com/F7H/GGVS/JGGTGNKB/F7HGGVSJGGTGNKB.jpg&filename=20180427_192348.jpg)
- Take two equal parts of putty mix them evenly to form a compound
- Apply it on the pin except the inserting part
- Give it a good shape...Let it harden.
- After hardening rub it wit a sandpaper and give nice finishing
![20180427_193003.jpg](/proxy/?url=https://content.instructables.com/FPC/V2I3/JGGTGOK2/FPCV2I3JGGTGOK2.jpg&filename=20180427_193003.jpg)
Now bend the terminal wire to both sides
ATTACHING THE SIDE GRIPPERS
![20180427_183733.jpg](/proxy/?url=https://content.instructables.com/F5J/ZRTT/JGGTGMUW/F5JZRTTJGGTGMUW.jpg&filename=20180427_183733.jpg)
According to your design .
- place the grippers on stand.
- take a small piece keep it over and screw it or pin it
THE MOST IMPORTANT THING-CHECKING THE TERMINALS
![micro usb.png](/proxy/?url=https://content.instructables.com/F8N/EEJX/JGGTGZGJ/F8NEEJXJGGTGZGJ.png&filename=micro usb.png)
The important thing is the terminals, so it should be rightly aligned.
- align the terminals at the center of base.
- connect them correctly.
- the right side of the terminal should be +ve for usb male pin
- the most left terminal is GND
- the other terminals are not necessary for charger
PAINT JOB
![20180427_213033.jpg](/proxy/?url=https://content.instructables.com/FVO/ZRH9/JGGTGOY6/FVOZRH9JGGTGOY6.jpg&filename=20180427_213033.jpg)
![20180427_213452.jpg](/proxy/?url=https://content.instructables.com/FQI/HMVF/JGGTGP41/FQIHMVFJGGTGP41.jpg&filename=20180427_213452.jpg)
![20180427_222159.jpg](/proxy/?url=https://content.instructables.com/FH3/OQG7/JGGTGP6Z/FH3OQG7JGGTGP6Z.jpg&filename=20180427_222159.jpg)
![20180427_195235.jpg](/proxy/?url=https://content.instructables.com/FWB/9E77/JGGTGONJ/FWB9E77JGGTGONJ.jpg&filename=20180427_195235.jpg)
![20180427_224316.jpg](/proxy/?url=https://content.instructables.com/F8B/OX1M/JGGTGQ5R/F8BOX1MJGGTGQ5R.jpg&filename=20180427_224316.jpg)
- First lightly sand the body with sand paper.
- apply a coat of primer
- rub it again with sand paper to give smooth finish
- Apply paint of your choice.
- Do the same with usb pin
- Fix all the parts
CHARGE YOUR PHONE
![20180427_225004.jpg](/proxy/?url=https://content.instructables.com/F4R/TPA8/JGGTGQAG/F4RTPA8JGGTGQAG.jpg&filename=20180427_225004.jpg)
![20180427_225514.jpg](/proxy/?url=https://content.instructables.com/F9O/73N2/JGGTI4LP/F9O73N2JGGTI4LP.jpg&filename=20180427_225514.jpg)
Its finished!!!!!!!!!!.
Enjoy your wireless charger stand....
THANK YOU FOR READING. SURE COMMENT ON THIS