DIY Pallet Lamp (Rustic)

by zaclewis98 in Workshop > Lighting

1868 Views, 44 Favorites, 0 Comments

DIY Pallet Lamp (Rustic)

IMAG0442_1.jpg
IMAG0438.jpg

What inspired me?

Designing around up cycling and reusing, I love to complete projects orientated around pallet wood. This is a huge modern movement that incorporates rustic pallet wood and turning it into new and exciting products and even art.

Needing a new lamp and an excuse to make something, I quickly drew out a simple lamp design. I wanted a angle poise feel to it. So, I settled with a design and thought out some measurements.

What will you need?

- pallet wood (new or old)

- Jig saw or another type of wood saw

- ruler, tri-square and pencil

- 4mm drill bit

- 10mm drill bit

- Drill driver

- 50mm screw

- 75mm screw

- 3 washers, 3 nuts and 3 bolts (at least 45mm long)

- adjustable spanner

- Dark wood stain and cloth

- LED circuit, battery or USB

- three cable ties

Step 1 : Cutting

IMAG0468.jpg
IMAG0430.jpg

Before I started to cut the pieces to shape, I made sure each piece would fit onto a single plank by using my pencil and ruler to trace out each piece on the plank. After a few adjustments with the positioning i clamped the wood up and began to cut each piece. Using the jug saw a started to Cut away all unwanted material, i didnt need to be as careful as i planned to use a fine and sander to ensure a clear, flat surface.

Step 2 : Drilling

IMAG0413.jpg
IMAG0418.jpg

I decided to drill the holes next and using a simple own I marked on where I wanted them to go before using a screw to indent where I needed the hole to be, just to prevent the drill bit from slipping. Using the 10mm drill bit, I placed two holes at either end on the middle piece, one hole at the top of the first piece and one more on the last piece at the top.

Step 3 : Sanding

WP_20160822_111.jpg
WP_20160822_113.jpg

The second most important factor in any product is the finish. And before any stain was added, I needed to sand all the surfaces. Using 100 grit sand paper I gently removed the cut marks left after using the jig saw and I rounded over some if the edges to acquire a softer appearance. Once the edges are done, I used 200 grit sand paper to get a smooth finish all over the lamp.

Step 4 : Checking and Staining

IMAG0469.jpg
IMAG0459.jpg

Before any stain was added, I decided to quickly construct my lamp just in case I made any errors when actually cutting the pieces. I used three M8 Bolts and hex nuts to secure al of the pieces in the correct position. Once I was sure about both positioning and size, I began to stain.

To finish the wood, I quickly brushed off any sawdust from the surface with a rag and using a cloth, I dabbed on some oak, dark stain. I wanted a very dark surface, however, if you wish to have a lighter or even darker lamp then feel free to use lighter or darker wood stain.

Step 5 : Construction

IMAG0464.jpg
IMAG0461.jpg
IMAG0465.jpg
IMAG0467.jpg
IMAG0463.jpg
IMAG0462.jpg
IMAG0466.jpg

As mentioned in the last step, I used three M8 bolts to secure each piece together. On top of the three M8 bolts, I used three M8 nuts, and washers to ensure the bolts and nuts don’t indent the surface. Wingnuts would have been a much better choice.

Step 6 : the Tin and Circuit

The tin was just an ordinary tin from the super market that I cleaned with s sponge and then went over with some wire wool to get rid of any other bits that the sponge missed. I drilled a 5mm hole in the top of the tin in the very centre. I then used the same drill bit to drill a hole in the top side of the tin. This is for the cord to exit the lamp.

The light is a very simple circuit I acquired from kitronik. https://www.kitronik.co.uk/2132-white-usb-lamp-kit.html I also added two long wires to the circuit as I didn’t want to mount the led directly to the circuit. To secure the circuit inside, I just used some double sided tape. I also used a few zip ties to attach the cable to the body of the lamp.

Finished

IMAG0439.jpg
IMAG0440.jpg

Thank you so much for reading this Instructable, even if you clicked onto the by accident thank you. Every view counts. I love these mini projects as it gives you people, my viewers a quick and simple project to try at home, please feel free to comment, follow and favourite for more amazing Summer DIY projects like this one.