DIY Multi-Room Audio

Hey! everyone My name is Steve.

Today I'm going to show you How to Make a Wifi Audio Streamer using very fewer parts and it's better than chrome cast Audio and you can use it as multi-room setup and it can connect up to 10 Speakers

Click Here to See The Video

Let's Start

Input Power

• 5V DC

Output Power

• 2 X RCA for Stereo Audio Output

LCSC

----------------------------------------------------------------------

• DC Socket - http://bit.ly/33RkqBF
• Stand-Off - http://bit.ly/2z8qpDU
• RP-SMA Female Jack - http://bit.ly/2z8qpDU
• 3db antenna - http://bit.ly/2z8qpDU

LCSC 8$ OFF on your first order - https://lcsc.com/?href=STEVE&source=referral

----------------------------------------------------------------------

Banggood

----------------------------------------------------------------------

• Up2Stream WiFi Module - https://goo.gl/wLck2Q
• Aluminium Case - https://goo.gl/wLck2Q
• PCB Stand-Off - https://goo.gl/wLck2Q
• Heat Shrink Tube - https://goo.gl/wLck2Q
• RCA Connector - https://goo.gl/wLck2Q
• Rubber Pad - https://goo.gl/wLck2Q
• Drill Bit - https://goo.gl/wLck2Q
• RP-SMA Female Jack - https://goo.gl/wLck2Q

----------------------------------------------------------------------

Amazon

----------------------------------------------------------------------

• Up2Stream WiFi Module - https://amzn.to/2xo57kg
• Aluminium Case - https://amzn.to/2xo57kg
• PCB Stand-Off - https://amzn.to/2xo57kg
• Heat Shrink Tube - https://amzn.to/2xo57kg
• RCA Connector - https://amzn.to/2xo57kg
• Rubber Pad - https://amzn.to/2xo57kg
• Drill Bit - https://amzn.to/2xo57kg

----------------------------------------------------------------------

Aliexpress

----------------------------------------------------------------------

• Up2Stream WiFi Module - http://bit.ly/2WZgs5H
• Aluminium Case - http://bit.ly/2WZgs5H
• PCB Stand-Off - http://bit.ly/2WZgs5H
• Heat Shrink Tube - http://bit.ly/2WZgs5H
• RCA Connector - http://bit.ly/2WZgs5H
• Rubber Pad - http://bit.ly/2WZgs5H
• Drill Bit - http://bit.ly/2WZgs5H

----------------------------------------------------------------------

Note - Please see the images for better understanding

Today's Article is Sponsored by lcsc.com

They are the Largest Electronics Components Supplier From China Ready to Ship within 4 Hours and they ship World Wide

Note - Please see the images for better understanding

• I Used a Philips Head Screw Driver to Open the Enclosure
• And Then I placed the Up2Stream module on top of the Enclosure and used a Center Punch to Punch 4 Holes
• And then I used a 3mm Drill Bit to Drill the Punches

Note - Please see the images for better understanding

I used Center punch for marking of 2 RCA Jack, DC jack and wifi antenna

and then i've drilled 4 holes with a drilling machine

Note - Please see the images for better understanding

• First, I've installed DC Socket
• And then I've installed 2 RCA socket
• And then I've installed Wifi antenna socket

Note - Please see the images for better understanding

I used 4 stands off to give it some clearance

Note - Please see the images for better understanding

This board comes with 2 wire one is audio output wire and one is power input wire

The problem is the audio output wire has 4 wire and you only need 3 wire one for Right channel output one for Ground and one for Left channel output,

The fourth wire is WPS you don't need it

So, I've cut the forth wire

Note - Please see the images for better understanding

• First, i've connected the wifi wire to the board
• I used 4 screws to fit the board into the enclosure

Note - Please see the images for better understanding

• First I've soldered the 3 wires to the RCA socket
• And then I've soldered the 2 wires to the DC socket

Note - Please see the images for better understanding

• I used 4 screws to fit the back panel
• And then I used 4 screws to fit the front panel

Note - Please see the images for better understanding

I used some rubber feet on the bottom

Note - Please see the images for better understanding

Connection

• First I've connected the RCA Jack
• Second I've connected the 5v Dc Jack
• Third I've connected the Wifi Antenna

Speaker

• I used my Bluetooth Speaker as my Speaker output Via Aux input

Note - Please see the images for better understanding

• You need MUZO App to setup
• Open MUZO App Select " Add another MUZO compatible speaker "
• Select BUSH
• Select Setting
• Now connect to "Stream System"
• Now select the Wifi you want your speaker to connect and enter the Password
• Now you can keep your speaker Name
• You are all Set
• Now go to My Music
• And Play the Song
• You can control Your Volume There
• You Can connect up to 10 Speaker and can play different songs

Enjoy

Note - Please see the images for better understanding

Click Here to See The Video

You Just Made It

Thank you for visiting my Instructables Stay tuned for next Projects