Chess WARS

We made a chess but merged with star wars related characters.

You will be looking at a normal chess game with star wars characters.

• 3-D Printer
• A computer for Tinkerchad
• 3-D printer filament

(If you get stuck please feel free to take a look at these pictures!)

Part 1: Legs

1. Start with 4 normal cylinders.
2. Place 1 on top of each other (repeat this process until you have 3 cylinders on top of each other on each side.

Part 2: Feet and body

1. Once you're done with the legs
2. grab a square and stretch it out to fit all the corners. copy and paste the now rectangle over the other one.

Part 3: Front body and face

1. Place 4 ramps on top all the way in front and sink them into the body until the data on the left says "-14.00".
2. Place 4 squares up in front of the ramps.
3. Take out a square and then place it in front of the 4 squares with half of the square in and the other half out.
4. Stretch the square into a rectangle.

Part 4: Weapons

1. Get 2 cylinders and stretch them out so their long but still circular. Place them under the face of the vehicle.

Part 5: Final body arrangements.

1. Place a square behind the ramps you placed in part 3, step 1.
2. Stretch the square out to make it fit the size of the rectangle below.
3. Make sure to align the square's size with the ramp's size.

Step 1: Starter Body

1. Start with a normal cylinder and a half sphere.
2. Pull the sphere up to give the cylinder some space to get taller.

Step 2: Body tilt

1. Tilt it at a 19 degree angle it doesn't have to be perfect just don't tilt it too much you have to leave little space for the front wheel.

Step 3: Wheel

1. Get a ramp, square, and another ramp and set it in this order. Ramp facing to the right, square in the middle, ramp facing to the left.
2. Get another square make it tall then thin it out and tilt it at a 37-degree angle and make it connect with the square and then slightly make the blue touch with R2D2's body.

Step 4: Projector/Eye

1. Get yet another square this time make it smaller and then get a half-sphere shrink it until it looks like a 2d circle and then put it right on the square.
2. Tilt the square at a 12-degree angle.

Part 1: Body

Place a sphere and color it black

Part 2: Head

Place a orange cylinder and shrink it.

Part 3: Eye

Copy and paste the same cylinder you have as its head and shrink it.

Get the same cylinder copy and pasted and yet again shrink it but smaller and make it red.

Part 1: Front

Place 2 triangles and stretch them and place them like so in the picture.

Part 2: Body

grab a square and stretch it out. Copy and paste that rectangle under the original and make it smaller.

At the end or so, get another triangle but stretch it and make it smaller just like how it is in the picture.

Part 3: Side color

Get a square and stretch it out so its able to peak out of both sides. Place this inside make sure its peaking out of both sides.

Make sure to place this around the front of the body.

Part 4: Back of the body

Place a square and shrink it more the body side.

Place a square in the other side but make sure to leave a hole in the middle of both squares. (If you're confused check the pictures)

Put another square under to have some floor in the gap.

Once you're done with that get another square and make it paper thin.

Put it on the sides of the gap.

Part 5: R2D2

Get the R2 you just finished doing a couple steps ago and paste it into this creation. Make the R2D2 smaller to fit into the gap.

Part 6: Windshield

Get the same black window, copy and paste it and make it smaller you can also make it white to tell the difference. Place these "corners" on the edge of the window.

Part 7: Thrusters

Get 2 cylinder and place them on their side.

Place the cylinders on the side of the back body.

Place another 2 cylinders like this on the bottom of the first cylinders, make sure to leave some space between the top cylinder and bottom cylinders.

Repeat this process on the other side.

Part 8: Thruster Fire

Grab a Paraboloid and place it behind all the cylinders at the end. Color it any color in this case I made it pink.

Part 9: Wings

Copy and paste the walls you used for the droid hole in Part 4, semi last sentence. Tilt it like how it is in the pictures above and place 2 on each side one facing up and one facing down like an X!

Part 10: Weapons

Get some cylinders and make them thin and long attach the end of the cylinders with the wings repeat this process for each wing.

Part 1:

The legs were created by 4 cylinders, and you stack one on the other, 2 on each side;.

Copy the legs and make the arms almost touch each other but color them black.

The shoes must be fully black, you can just make a rectangle out of a square.

The hands have to be in different signs make the left hand stretched a tiny bit.

The lightsaber must have two thin cylinders and have 1 diamond make the diamond small, the handle gray, the 2 saber green.

Part 2:

The head is just a sphere without any adjustments, but the color is supposed to be peach.

The body is a cylinder, it isn't shortened as isn't thin as the arms and legs.

The hair is a drawing and is meant to be hollow to make proper adjustments to fit the hair on the head.

The hip is a diamond as is shortened black with proper adjustments the hip can be escalated to be small enough to fit.

(Sorry there wasn't enough pics)

Part 1: Body

Place a sphere and make it big.

Part 2: Wing Connection

Grab a cylinder and make it smaller and short place it on the left side of the sphere. Place another one of these on the right side of the sphere.

Part 3: Wings

Get a polygon and make it bigger.

Place 1 of these at each end of the wing connections.

Part 1: Feet and legs

Go to creatures and character all the way on the right and choose the shoe.

Place the shoes a reasonable amount of distance away from each other.

Make the shoe red

Part 2: Body

Get a paraboloid which is the white and round rhombus

Stretch it out and make it fitting to the legs but leave some space after the legs to make it look like how it is in the picture.

Get a cylinder and stretch it out to fit the "skirt", don't make it too stretched!

Part 3: Head

Get a sphere and make it bigger to fit the size of the cylinder "body".

Part 4: Arms and weapon

Get a cylinder shrink it make it thin and tilt it to a 45 degree angle. Once done with this copy and paste the arm to the other side.

Copy and paste the arms you have and tilt them to be sitting on their side and facing straight. After you have this place the arm at a 22.5 degree angle and connect it the first arm do the same thing you did on the other side.

Thin a cylinder down and copy and paste 4 thin cylinders each on top of each other.

Place 2 cylinders

Place different angled cylinders

Place a cylinder at a 90 degree angle as a hip

Place a cylinder as a body

Place a cylinder as a arm which should be at a 90 degree angle.

Copy and paste the arm on the other side

We made the head details by comparing with a pictures.

Head part 1: The head was made out of two eggs stretch out the eggs and the half sphere the nose was made out of a tiny after making the right portions sphere the tooth is made of tiny triangle

Body Part 2: use a cylinder for the body and the bandolier was made out of tube stretched while making it thin.

Arms Part 3:Use two spheres to connect the arm while use the paraboloid and the cylinder to connect to the sphere the fingers are mini paraboloids

Legs part 4: Use Four paraboloids and 3 half spheres to of the half spheres are use for the feet the other sphere is meant to connect the legs to the hips

Part 1 The head: The was made out of drawing and made a shape to make the head look like Darth Vader and make it a shape

Part 2 the body, arms, and legs: the bod was made of 2 cylinders and were stretched to make a it and the arms were bent to make the hands normal, the legs are four cylinders and the shoes are in a category to access and make the body, arms, and legs make the body fully black

Part 3 the cape and the lightsaber: The cape is made out of 14 paraboloids stretched, now the lightsaber is made out of two cylinders and has a small diamond.

Get shoes from creatures and characters

Get a paraboloid and place a cylinder on top, thin the cylinder.

Get a small thin cylinder and place it in the 90 degree angle and place another one of these on the other side.

Get another small thin cylinder and place it facing up and do the same thing for another arm facing down connect the left arm with the arm looking facing up and the right arm with the one facing down.

Place a sphere on top of the cylinder.

We detailed hair with mini sized cylinders.

You 57 paraboloids for the cape and the for the base of the king stretch 56 paraboloids and surround it across the base put a cylinder inside the capes to give support to the head. Use a sphere to be the head and surround it with ten tubes to make the hood

Part 1: Stretch a square and also make it thin.

Part 2: Shrink a square and color it.

Part 3: Place a lot of these to fit the exact shape of the stretched square.