Broken Guitar Fix & Paint Job

by scottdesignworks in Workshop > Woodworking

3266 Views, 31 Favorites, 0 Comments

Broken Guitar Fix & Paint Job

beauty shot white.jpg
before.jpg

This guitar came to me as basically garbage. Although brand new, it had been damaged in shipping and had a big hole in the top, several long cracks, loose bridge, etc… As an amateur luthier I thought it would be fun to see if I could fix it. It hung on the wall for a long time before I started.

Supplies

Busted guitar (Cordoba C7 CD/IN), thin CA glue and accelerator, wood glue, scrap cedar, sandpaper, shellac, Testors enamel paints, mineral spirits, Testors black enamel paint pen, masking tape, spray on polyurethane.

Tools: Clamps, scissors, small paint brushes

Stabilize the Loose Parts

clamps3.jpeg
clamps1.jpeg

The top was lifting next to the missing piece and the bottom side had sprung slightly away from the top. To get it all back in line took some wood glue and several clamps.

Close the Cracks and Reattach the Bridge

glued cracks cu.jpeg
glued cracks.jpeg

I wicked thin CA glue into the cracks and under the bridge one at a time using my hands as the clamps and using accelerator to set the glue quickly.

Map Out the Hole

hole rubbing .jpeg
hole rubbing cutout.jpeg

I taped some paper over the hole and rubbed with a crayon to mark the shape of the hole. Then I cut out the shape until it fit.

Re-glue Loose Brace and Add Some Wood

hole .jpeg
hole2 reglue brace and new wood.jpeg
hole3 more new wood.jpeg

I glued in two thin pieces of cedar to attach the patch to.

Patch the Hole

hole4 filled with patch.jpeg

I cut some cedar into the shape of the hole, and sanded the edges until it fit well. Then I glued it in with CA glue.

Sand the Top

sand superglue level.jpeg
sanded level.jpeg

Sand the top to flatten the patch, cracks, and superglue squeeze out. I put down some masking tape to contain the area where the finish would be damaged. Then sanded everything until reasonably flat.

Seal Bare Wood With Shellac

shellac to seal.jpeg
shellac2.jpeg

Design the Paint Job

t sanded patched  front image .jpeg
t sanded patched front computer drawing.jpeg

I photographed the guitar body from directly overhead, then drew and edited a plan on the computer until I was happy with it.

Grid the Design Onto the Guitar

transfer with grid2.jpeg

I made a square grid pattern on the guitar with string and tape, and then drew a matching grid on the paper with my design.

Transfer the Lines With a Sharpie

transfer with grid4.jpeg
transfered.jpeg

This is the trickiest part. It’s tedious to get all the lines in the right place. I used a red Sharpie at first, but switched to black as it was easier to see.

Mix Paint

trial paint test mix.jpeg

I wanted three values of blue, so I bought a light blue and a dark blue, and mixed the two to get the medium blue.

Test Paint

trial paint test.jpeg
trial paint test1 .jpeg

I painted a test and decided that the dark blue was too dark by itself. So I added light blue to both the dark and the medium until I had a nice range of values.

Paint the Colors

tuxing in colors1.jpeg
tuxing in colors2.jpeg
tuxing in colors4.jpeg

Using my paper map I put in all the areas of the light blue first, then the dark, then the medium.

Add the Black Lines

tuxing in colors5 outlined .jpeg
tuxing in colors6.jpeg

Using the paint pen I drew in all the lines as smoothly as I could. I went back in with the colors to smooth out any bumps in the lines. After all the paint was dry I used denatured alcohol to erase any Sharpie marks still visible. Then a couple coats of clear poly spray gives a little protection to the paint.

Done. String It Up and Play!

beauty shot.jpeg
IMG_7870.jpeg