(bitter)sweet Hair Pins

by bartworker in Workshop > Woodworking

31225 Views, 589 Favorites, 0 Comments

(bitter)sweet Hair Pins

DSCF0607.JPG
DSCF0611.JPG
DSCF0616.JPG
Unless the fact that I prefer my wife getting her (very) long hair unpinned sometimes it might be useful to pin things up.
Usually she uses chopsticks (well that's a nice hack!) but as a maker I thought her hair deserved better.

So here's a short I'ble to show you how I transformed some pieces of hardwood a friend wanted to burn (are you kidding?!) into a bunch of hair pins.

All you need is some scrapwood, a miter saw & a belt sander.

Making wooden hair pins is accessible to every woodworker. You can make them as complex as you want or just keep it simple. I made a few examples just to show how far you can go - and if you google a bit you'll see you can go veeeeeeeery far. Mine's are peanuts, compared to some.

Bittersweet? Well, while making the one with the knife handle I was thinking this could be a severe selfdefence tool. It's completely legal - just an innocent hair pin - but in the hands of a furious women this tool could do just a little bit damage.
I'd think twice before aggressing someone in the streets...

Special thanx to member AngryRedhead to transform some of my DIY-translations into decent English ;)

Slice It

DSCF0581.JPG
DSCF0582.JPG
DSCF0583.JPG
DSCF0584.JPG
Gather some (scrap) hardwood - I got some oak (the light one) & meranti.

Use a miter saw to cut slices of about 1/3 inch wide and 10 inches long (10mm-300mm).

Note: My wife calculated that for 'average long hair' everything between 8 & 9 inches should be okay (ornament included). This means that mine's are just a bit too long to be comfortable.

Go Triangular

DSCF0585.JPG
DSCF0586.JPG
DSCF0587.JPG
DSCF0588.JPG
DSCF0592.JPG
DSCF0593.JPG
DSCF0594.JPG
Aim is to build conical pins, so you'll have to cut some piramids.
If you want to go sofisticated: cut out your design first.

Note: be aware that this kind of precision cutting with the miter saw can be a dangerous job. Instead of keeping the slice of wood in place manually I always clamp it with a second piece of wood (visible on the picture left above). Most miter saws have ready-made side clamps so you just have to clamp a piece of wood under the clamp & on the slice. Secure the whole & start cutting in all safety.

Round It

DSCF0589.JPG
DSCF0590.JPG
DSCF0595.JPG
Use a belt sander & have fun shaping.

Decorate & SAND

DSCF0603.JPG
DSCF0604.JPG
DSCF0606.JPG
With a grinder you can do some great work. Use it, that inspiration!

What follows is sanding. A LOT of sanding...

Two things I learned:
- the oak is way much harder than the meranti
- the more brutal the sanding, the greater the collateral damage - exit one hair pin

Finish!

DSCF0607.JPG
DSCF0611.JPG
DSCF0616.JPG
You'll finish that job with natural oil - walnut stays my ultime favourite. Wipe the excess with a towel.

Done!

Hope you liked it & thanx for watching!

Bonus: the Knifed Hair Pin

DSCF0596.JPG
DSCF0597.JPG
DSCF0598.JPG
DSCF0599.JPG
DSCF0600.JPG
DSCF0602.JPG
No big deal. Cut a few holes to fake the rivets, make a nice round stick, smash it with some cyanoacrylate or bicomp in the holes, cut & start sanding.