Adventures of a Can Tab
![IMGP4363.jpg](/proxy/?url=https://content.instructables.com/FA5/50JZ/KWT9C1L7/FA550JZKWT9C1L7.jpg&filename=IMGP4363.jpg)
How do you use can tabs? Obviously to open cans. What after that? It can be recycled all together with a can. But I usually detach them from cans: they could be handy in some small projects around a house.
Picture Hangers
![IMGP4376.jpg](/proxy/?url=https://content.instructables.com/F1V/MW9Q/KWT9C1O2/F1VMW9QKWT9C1O2.jpg&filename=IMGP4376.jpg)
![IMGP4375.jpg](/proxy/?url=https://content.instructables.com/FOP/IZ8E/KWT9C1O1/FOPIZ8EKWT9C1O1.jpg&filename=IMGP4375.jpg)
Tabs small size and flexibility allow to use it as picture or placard hangers.
Frame Backup Clips
![IMGP4366.jpg](/proxy/?url=https://content.instructables.com/FOC/BQ3C/KWT9C1PI/FOCBQ3CKWT9C1PI.jpg&filename=IMGP4366.jpg)
![IMGP4367.jpg](/proxy/?url=https://content.instructables.com/F7B/MRRC/KWT9C1PJ/F7BMRRCKWT9C1PJ.jpg&filename=IMGP4367.jpg)
You can use it as backup clip for DIY photo frame.
Transistor Cooler
![IMGP4374.jpg](/proxy/?url=https://content.instructables.com/FMF/1VU5/KWT9C1Q9/FMF1VU5KWT9C1Q9.jpg&filename=IMGP4374.jpg)
![IMGP4377.jpg](/proxy/?url=https://content.instructables.com/FPL/H6WJ/KWT9C1RQ/FPLH6WJKWT9C1RQ.jpg&filename=IMGP4377.jpg)
Tabs (the same as cans) are produced out of aluminum alloy and that makes them good heat conductor. Here you see I attached two tabs to a transistor as a cooler. How effective it is? Hard to tell, I did not make any measurement but I it dissipates at least part of heat energy produced by electronic device.
Precision Screwdriver Stand
![IMGP4352.jpg](/proxy/?url=https://content.instructables.com/FND/9GHU/KWT9C1T5/FND9GHUKWT9C1T5.jpg&filename=IMGP4352.jpg)
![IMGP4357.jpg](/proxy/?url=https://content.instructables.com/FYG/SORG/KWT9C1V9/FYGSORGKWT9C1V9.jpg&filename=IMGP4357.jpg)
I have several precision screwdrivers. They are from different vendors an of different length so to keep it safe and handy I had to make special stand for them. First picture here shows element of the stand: wooden blocks with attached tabs and long screw. Second picture shows assembled stand.
Separators for Drill Bit Holder
![IMGP4372.jpg](/proxy/?url=https://content.instructables.com/FWU/3GZT/KWT9C1WO/FWU3GZTKWT9C1WO.jpg&filename=IMGP4372.jpg)
I had IKEA pen/pencil holder which I did not use much. I found use in it as a place to keep various drill bits. In the middle of the holder I glued wooden cylinder with drilled hole inside of it. On the edge of the holder cup I installed tabs. Some narrow drill bits I keep inside tab holes, some wider bits are in spaces between tabs.
Conclusion
![IMGP4364.jpg](/proxy/?url=https://content.instructables.com/F9N/IKW3/KWT9C1MM/F9NIKW3KWT9C1MM.jpg&filename=IMGP4364.jpg)
OK, as of now I am out of tabs and out of ideas. What do you make with can tabs?