A Simple and Reliable Door Alarm System

by chrisjlionel in Circuits > Electronics

2571 Views, 24 Favorites, 0 Comments

A Simple and Reliable Door Alarm System

WP_20150712_005.jpg

Before explaining "how to make?"

I'll tell you answers for "Why to make?"

  • Has your child ever opened the front door and walked outside without your knowledge?
  • Do you know if someone trying to open your door from outside?

So its better to have a door alarm for safety purposes.

There is ON/OFF provision to avoid frustration

My Alarm is different from the cheep magnetic one.

I am latching the relay to sustain the buzzer till the switch is manually turned OFF.

So definitely you will be notified if some one tries to open the door that's why this one is Reliable.

I developed this circuit from patrick's (engineering shock) idea by implementing latching concepts which i learned from mechatronics. Check his trip wire circuit you will understand.

Requirments

WP_20150709_005.jpg
WP_20150709_004.jpg
WP_20150709_002 copy.jpg
55a2515e2e7fb6d82300018d.jpeg
55a251c745bceb4326000041.jpeg
  1. 2N2222 - NPN Transistor (any npn will work fine) - 1
  2. 1k ohms resistor - 1
  3. 100 ohms resistor - 1
  4. DPDT relay - 1 (if you follow circuit - A)
  5. DPST realy - 2 (if you follow circuit - B)
  6. LED diffused red - 1
  7. 12 v piezo buzzer
  8. 9 v battery with snap
  9. duct tape *optional (step -4)
  10. magnetic reed switch with small piece of magnet *optional (step -4)
  11. Tools to work

If you got DPDT relay stick with CIRCUIT - A

If not... stick to CIRCUIT - B

Use Circuit Wizard to Make Pcb (optional)

WP_20150709_047.jpg
WP_20150709_046.jpg
Capture 221.jpg
WP_20150709_039.jpg
WP_20150709_037.jpg
WP_20150709_041.jpg
WP_20150712_013.jpg
WP_20150712_014.jpg
  1. select --> PCB layout at the bottom of UI
  2. then select --> Artwork
  3. print the doc with a laser printer
  4. then transfer toner to copper clad board
  5. use ferric chloride to etch
  6. make holes
  7. solder

Search for a tutorial to make PCB

I've just used a permanent marker to draw the Artwork in copper clad board.

Don't forget to clean the clad board with IPA (isopropyl alcohol ) before starting.

Properly dispose of used ferric chloride solution.. sorry it will become cupric chloride (copper 2 chloride) after etching copper anyhow dispose of it.

Download the attachment and open with Circuit Wizard to simulate (circuit - B)

Downloads

If You're Not Interested in PCB Then Skip the Previous Step

WP_20150712_001.jpg
WP_20150712_003.jpg
WP_20150712_006.jpg
WP_20150712_002.jpg

Just connect components as shown in the diagram.

Preparing the Trigger Part

WP_20150713_016.jpg
WP_20150713_011.jpg
WP_20150713_017.jpg
WP_20150713_025.jpg
WP_20150713_030.jpg

You got two options here.

If your lock is similar to mine,then you're lucky.

Follow my steps

Just measure and cut duct tape suitable for your lock.

Use a two piece of wire as shown

It will close the circuit when the door closed. this mechanism replaces the push to break switch in circuit

Other option : you need a magnetic reed switch and a piece of natural magnet

Mount, Install & Turn ON == Feel Secured

WP_20150713_036.jpg
WP_20150713_037.jpg
WP_20150713_035.jpg