3D Spinning Pendant
![Swanky Jofo-Rottis (3).png](/proxy/?url=https://content.instructables.com/FMO/VFOM/KYWZO8S4/FMOVFOMKYWZO8S4.png&filename=Swanky Jofo-Rottis (3).png)
![Swanky Jofo-Rottis (8).png](/proxy/?url=https://content.instructables.com/FTP/7QIY/KZ2PF6OM/FTP7QIYKZ2PF6OM.png&filename=Swanky Jofo-Rottis (8).png)
![Swanky Jofo-Rottis (9).png](/proxy/?url=https://content.instructables.com/FH5/SU09/KZ2PF6OL/FH5SU09KZ2PF6OL.png&filename=Swanky Jofo-Rottis (9).png)
This is a 3D spinning pendant it is all done on TinkerCaD.It is a 3 piece 1 spinning part it is 85x85It took me about 2 weeks and a half to make this pendant. It is unique Because you could use it even as a pocket watch pop on any chain even if you want you could change the colors to your liking.
Supplies
TinkerCAD, PLA Filament, Voxel 3D Printer, Necklace chain
First Step
![Cool Bigery-Jaiks (1).png](/proxy/?url=https://content.instructables.com/F2Y/2W1O/KYWZOCAZ/F2Y2W1OKYWZOCAZ.png&filename=Cool Bigery-Jaiks (1).png)
The first step is to add-a-ball put the height to 1.
Second Step
![Cool Bigery-Jaiks.png](/proxy/?url=https://content.instructables.com/FFA/2XLZ/KYWZOCCV/FFA2XLZKYWZOCCV.png&filename=Cool Bigery-Jaiks.png)
![Smooth Tumelo-Snicket (3).png](/proxy/?url=https://content.instructables.com/FFZ/IX7M/KYWZOC0K/FFZIX7MKYWZOC0K.png&filename=Smooth Tumelo-Snicket (3).png)
The second step is to make the width and length 80mm.
Third Step
![Cool Bigery-Jaiks (2).png](/proxy/?url=https://content.instructables.com/FVX/SBFH/KYWZOD2A/FVXSBFHKYWZOD2A.png&filename=Cool Bigery-Jaiks (2).png)
![Cool Bigery-Jaiks (3).png](/proxy/?url=https://content.instructables.com/FNU/HWZG/KYWZOD2B/FNUHWZGKYWZOD2B.png&filename=Cool Bigery-Jaiks (3).png)
![Cool Bigery-Jaiks (4).png](/proxy/?url=https://content.instructables.com/FHL/RHED/KYWZOD2C/FHLRHEDKYWZOD2C.png&filename=Cool Bigery-Jaiks (4).png)
The third step is to copy and paste another Circle End to one of the circles you would like to cut in half.
Fourth Step
![Epic Trug (10).png](/proxy/?url=https://content.instructables.com/F8J/NA3Z/KYWZOC0X/F8JNA3ZKYWZOC0X.png&filename=Epic Trug (10).png)
![Epic Trug (8).png](/proxy/?url=https://content.instructables.com/FF5/YYYM/KYWZOC0V/FF5YYYMKYWZOC0V.png&filename=Epic Trug (8).png)
![Cool Bigery-Jaiks (5).png](/proxy/?url=https://content.instructables.com/FJQ/3ETJ/KYWZODFK/FJQ3ETJKYWZODFK.png&filename=Cool Bigery-Jaiks (5).png)
The fourth step is to add a cylinder to the middle of the half-circle make the cylinder 6x6mm and the height 8mm then You have to make the Locking MechanicFirst, you will have to make a hole 3x3mm on the cylinder underneath or in the middle
if you want you could customize but make sure not to go any over the edges so I will show mine and it's not going over the edges.
Fifth Step
![Epic Trug (7).png](/proxy/?url=https://content.instructables.com/F17/2OBN/KYWZOC0O/F172OBNKYWZOC0O.png&filename=Epic Trug (7).png)
![Epic Trug (6).png](/proxy/?url=https://content.instructables.com/FPX/0ER6/KYWZOC0N/FPX0ER6KYWZOC0N.png&filename=Epic Trug (6).png)
![Epic Trug (5).png](/proxy/?url=https://content.instructables.com/FZG/XPS8/KYWZOC0L/FZGXPS8KYWZOC0L.png&filename=Epic Trug (5).png)
![Smooth Tumelo-Snicket (3).png](/proxy/?url=https://content.instructables.com/FFZ/IX7M/KYWZOC0K/FFZIX7MKYWZOC0K.png&filename=Smooth Tumelo-Snicket (3).png)
The fifth step You would like to make the other Circle you saved You would like to raise it 21 mm Then cut a circle in the middle not all the way down though because it will be Hollow they make it 95x95mm make the whole inside 86x86mm Cut a hole in the center middle and I will show it and the image.
Six Step
![Super Densor-Maimu.png](/proxy/?url=https://content.instructables.com/F8A/269Y/KYWZOC0P/F8A269YKYWZOC0P.png&filename=Super Densor-Maimu.png)
![Smooth Tumelo-Snicket (4).png](/proxy/?url=https://content.instructables.com/FOV/H8S8/KYWZOC0M/FOVH8S8KYWZOC0M.png&filename=Smooth Tumelo-Snicket (4).png)
The six-step You go back to the first step And just make a circle again 80x80mm Make a hole in it Make sure it's in the center Make the hole 7x7 mm If you want you also could customize I will show you one of my customers
Seventh Step
![Swanky Jofo-Rottis (7).png](/proxy/?url=https://content.instructables.com/FCN/6Q2I/KYWZOE0O/FCN6Q2IKYWZOE0O.png&filename=Swanky Jofo-Rottis (7).png)
The seventh step is to put it all together First you would like to Get the half-circle circle with the two cuts and put them together with something you can work on to make sure there is a gap in the middle.
Final Step
![Swanky Jofo-Rottis (2).png](/proxy/?url=https://content.instructables.com/FBM/I4HO/KYWZOC0Y/FBMI4HOKYWZOC0Y.png&filename=Swanky Jofo-Rottis (2).png)
Put it all together and printed.